3M 3M-Matic 8000a

To Next Page

To Previous Page

NA - ENG

April 2016

3M-Matic

™

Accuglide 3 - 2 Inch Taping Head

Page 30

Figure 10923  Upper and Lower Heads

Figure 10923 – Upper and Lower Heads

AccuGlide

™

3 - 2"

Main Page

Replacement Parts and Service Information3
Table of Contents7
Introduction13
Manufacturing Specifi Cations / Description / Intended Use13
How to Read and Use the Manual14
Importance of the Manual14
Manual Maintenance14
Consulting the Manual14
General Information15
After-Sale Service15
Safety17
General Safety Information17
Table of Warnings18
Number of Operators20
Residual Hazards20
Personal Safety Measures20
Component Locations22
Table of Warnings and Replacement Labels23
Power Requirements24
Operating Rate24
Operating Conditions24
Machine Noise Level24
Set-Up Recommendations25
Tape25
Tape Width25
Tape Roll Diameter25
Tape Application Leg Length - Standard25
Tape Application Leg Length - Optional25
Box Board25
Box Weight and Size Capacities25
Shipment, Handling, and Storage 5.1 Packed Machine Shipment and Handling28
Overseas Shipment Packaging (Optional)28
Handling and Transportation of Uncrated Machine28
Machine Storage28
Unpacking29
Uncrating29
Packaging Materials Disposal29
Installation30
Operating Conditions30
Space Requirements for Machine Operation and Maintenance30
Tool Kit Supplied with the Machine30
Machine Positioning30
Plastic Ties Removal31
Assembly Completion31
Taping Heads Completion32
Outboard Tape Roll Holder32
Preliminary Electric Inspection32
Main Power Machine Connection and Inspection32
Phases Inspection32
Theory of Operation33
Working Cycle Description33
Running Mode Defi Nition33
Normal Stop Procedure33
Emergency Stop33
Controls34
Box Width Adjusting Knobs34
Box Height Adjusting Crank34
On/Off Main Switch34
Emergency Stop Button (Latching)34
Safety Devices35
Blade Guards35
Emergency Stop Button35
Electric System / Circuit Breaker35
Set-Up and Adjustments36
Box Width Adjustment36
Box Height Adjustment36
Top Flap Compression Roller Adjustment36
Changing the Tape Leg Length36
Column Repositioning38
Run Boxes to Check Adjustment38
Operation39
Operator's Correct Working Position39
Starting the Machine39
Starting Production39
Tape Replacement39
Box Size Adjustment39
Cleaning39
Safety Devices Inspection39
Trouble Shooting41
Safety Measures (See Section 3)43
Tools and Spare Parts Supplied with Machine43
Inspections Performed Before/After Every Maintenance Operation43
Drive Belt Replacement43
Box Drive Belt Tensioning46
Additional Instructions50
Statement of Conformity50
Technical Documentation and Information51
Spare Parts / Ordering77
Intended Use85
Taping Head Contents / How to Use Manual87
Important Safeguards88
Specifi Cations90
Dimensional Drawing91
Installation92
Receiving and Handling92
Installation Guidelines92
Tape Leg Length92
Tape Width Adjustment92
Operation93
Tape Loading - Upper Taping Head94
Tape Loading - Lower Taping Head94
Maintenance96
Blade Replacement96
Blade Oiler Pad96
Cleaning97
Applying/Buffi Ng Roller Replacement97
Adjustments98
Tape Drum Friction Brake98
Applying Mechanism Spring99
One-Way Tension Roller100
Tape Leg Length100
Leading Tape Leg Length Adjustment100
Troubleshooting Guide101
Spare Parts/Service Information103
Recommended Spare Parts103
Replacement Parts and Service103
Equipment Warranty and Limited Remedy134
Intended Use135
Important Safeguards138
Specifi Cations140
Installation142
Receiving and Handling142
Installation Guidelines142
Tape Leg Length142
Tape Width Adjustment142
Operation143
Tape Loading - Upper Taping Head144
Tape Loading - Lower Taping Head144
Maintenance146
Blade Replacement146
Blade Oiler Pad146
Cleaning147
Applying/Buffi Ng Roller Replacement147
Adjustments148
Tape Latch Alignment148
Tape Drum Friction Brake148
Applying Mechanism Spring149
One-Way Tension Roller150
Tape Leg Length150
Leading Tape Leg Length Adjustment150
Troubleshooting Guide151
Spare Parts/Service Information153
Recommended Spare Parts153
Replacement Parts and Service153

3M 3M-Matic 8000a - Page 114

Table of Contents

Related product manuals