ABB Advance Optima magnos206 - Page 89

42/24-10 EN Rev. 9 Chapter 6: Gas Analyzer Operation 6-17
Menu Tree, continued
Menu
⏐
⏐ _ Calibrate
⏐ ⏐
⏐ ⏐ _ Manual calibration 0
⏐ ⏐
⏐ ⏐ _ Automatic calibration 0
⏐
⏐ _ Configure
⏐ ⏐
⏐ ⏐ _ Component specific
⏐ ⏐ ⏐ _ Measurement range 0
⏐ ⏐ ⏐ _ Filter 1
⏐ ⏐ ⏐ _ Pressure controller 2
⏐ ⏐ ⏐ _ Autorange 1
⏐ ⏐ ⏐ _ Alarm values 1
⏐ ⏐ ⏐ _ Active component 0
⏐ ⏐ ⏐ _ Module text 2
⏐ ⏐
⏐ ⏐ _ Calibration data
⏐ ⏐ ⏐ _ Manual calibration 1
⏐ ⏐ ⏐ _ Automatic calibration 1
⏐ ⏐ ⏐ _ Ext. controlled cal. 1
⏐ ⏐ ⏐ _ Output current response 1
⏐ ⏐
⏐ ⏐ _ Function blocks
⏐ ⏐ ⏐ _ Miscellaneous 3
⏐ ⏐ ⏐ _ Inputs 3
⏐ ⏐ ⏐ _ Outputs 3
⏐ ⏐ ⏐ _ Mathematics 3
⏐ ⏐ ⏐ _ Multiplexer/Demultiplexer 3
⏐ ⏐ ⏐ _ Measurement 3
⏐ ⏐ ⏐ _ Sample system 3
⏐ ⏐ ⏐ _ Calibration/Correction 3
⏐ ⏐
⏐ ⏐ _ System
⏐ ⏐ _ Date/Time 2
⏐ ⏐ _ Language 2
⏐ ⏐ _ Change password
⏐ ⏐ _ Setup system modules 2
⏐ ⏐ _ Save configuration 1
⏐ ⏐ _ Status signals 2
⏐ ⏐ _ Network 2
⏐ ⏐ _ Display 2
↓
↓
⏐
_ Maintenance/Test
⏐
⏐
⏐
⏐
_ System
⏐
⏐
⏐
_ Atm. pressure 2
⏐
⏐
⏐
_ Display test 0
⏐
⏐
⏐
_ Keyboard test 0
⏐
⏐
⏐
⏐
_ Analyzer spec. adjustm.
⏐
⏐
_ Pump 1
⏐
⏐
_ Atm. press. anlz 2
⏐
⏐
_ Calibration reset 1
⏐
⏐
_ Basic calibration 2
⏐
⏐
_ Measure cal. cell 1
⏐
⏐
_ Optical adjustm. 2
⏐
⏐
_ Phase adjustm. 2
⏐
⏐
_ Relinearization 2
⏐
⏐
_ Amplification optimization 2
⏐
⏐
_ Cross sensitivity adjustm. 2
⏐
⏐
_ Carrier gas adjustm. 2
⏐
⏐
_ Electr. zero cal. FID 2
⏐
⏐
_ Restart FID 1
⏐
⏐
_ Diagnostics/Information
⏐
⏐
_ System overview 0
⏐
⏐
_ Module specific
⏐
⏐
_ Raw values 0
⏐
⏐
_ Auxiliary raw values 0
⏐
⏐
_ Status 0
⏐
⏐
_ Controller values 0
⏐
⏐
_ Lamp intensity 0
⏐
⏐
_ Uras26 Status 0
⏐
⏐
_ Logbook 0