ABB Relion 670 series - Page 1031

Name Values (Range) Unit Step Default Description
V1LimHys 0.000 - 100.000 % 0.001 5.000 Hysteresis value in % of range and is
common for all limits
V1AngDbRepInt 1 - 300 Type 1 10 Cycl: Report interval (s), Db: In % of range,
Int Db: In %s
V2DbRepInt 1 - 300 Type 1 10 Cycl: Report interval (s), Db: In % of range,
Int Db: In %s
V2ZeroDb 0 - 100000 m% 1 1 Zero point clamping
V2Min 0.0 - 200.0 %VB 0.1 50.0 Minimum value in % of VBase
V2Max 0.0 - 200.0 %VB 0.1 200.0 Maximum value in % of VBase
V2RepTyp Cyclic
Dead band
Int deadband
- - Cyclic Reporting type
V2LimHys 0.000 - 100.000 % 0.001 5.000 Hysteresis value in % of range and is
common for all limits
V2AngDbRepInt 1 - 300 Type 1 10 Cycl: Report interval (s), Db: In % of range,
Int Db: In %s
V2AngMin -180.000 -
180.000
Deg 0.001 -180.000 Minimum value
V2AngMax -180.000 -
180.000
Deg 0.001 180.000 Maximum value
V2AngRepTyp Cyclic
Dead band
Int deadband
- - Cyclic Reporting type
UAmpPreComp5 -10.000 - 10.000 % 0.001 0.000 Amplitude factor to pre-calibrate voltage
at 5% of Vr
UAmpPreComp30 -10.000 - 10.000 % 0.001 0.000 Amplitude factor to pre-calibrate voltage
at 30% of Vr
UAmpPreComp100 -10.000 - 10.000 % 0.001 0.000 Amplitude factor to pre-calibrate voltage
at 100% of Vr
Table 741: VMSQI Non group settings (advanced)
Name Values (Range) Unit Step Default Description
3V0HiHiLim 0.0 - 200.0 %VB 0.1 150.0 High High limit in % of UBase
3V0HiLim 0.0 - 200.0 %VB 0.1 120.0 High limit in % of VBase
3V0LowLim 0.0 - 200.0 %VB 0.1 80.0 Low limit in % of VBase
3V0LowLowLim 0.0 - 200.0 %VB 0.1 60.0 Low Low limit in % of VBase
V1HiHiLim 0.0 - 200.0 %VB 0.1 150.0 High High limit in % of UBase
V1HiLim 0.0 - 200.0 %VB 0.1 120.0 High limit in % of VBase
V1LowLim 0.0 - 200.0 %VB 0.1 80.0 Low limit in % of VBase
V1LowLowLim 0.0 - 200.0 %VB 0.1 60.0 Low Low limit in % of VBase
V1AngZeroDb 0 - 100000 m% 1 0 Zero point clamping in 0.001% of range
V1AngMin -180.000 -
180.000
Deg 0.001 -180.000 Minimum value
V1AngMax -180.000 -
180.000
Deg 0.001 180.000 Maximum value
Table continues on next page
1MRK 502 066-UUS B Section 16
Monitoring
1025
Technical manual