50 Hanover Road, Florham Park, New Jersey 07932 www.ascovalve.com
Page 4 of 4 Form No.V6583R7
Torque Chart
Part Name Torque Value in Inch-Pounds Torque Value in Newton-Meters
terminal block screws 10 ± 2 1,1 ± 0,2
socket head screw 15 - 20 1,7 - 2,3
center screw 5 ± 1 0,6 ± 0,1
screw terminal
adapter
gasket
DIN terminal
adapter
socket head screw
socket head
grounding screw
Open-Frame Solenoid
Open-Frame Solenoid Open-Frame Solenoid
with Screw Terminals.
Socket head screw is
used for grounding.
with DIN Terminals.
tapped hole for
#10-32 grounding screw
(not included)
See
torque chart
above
terminal
block
screw
with 1/4 Spade Terminals
(5/32 hex key wrench)
(5/32 hex key wrench)
Indicates parts supplied
in Termination Module
Kit No. K256104
Figure 4. Open-frame solenoids
cover screw
cover gasket
cover
junction box gasket
junction box with
and grounding terminal
socket head screw
screw terminal block
(see note)
grounding screw
and cup washer
Junction Box Solenoid
Note:
Junction box with screw terminals
shown. With screw terminal
block removed, remaining parts
comprise the junction box for
spade terminal construction.
See
torque chart
above
or Screw Terminals
(5/32 hex key wrench)
1/2 conduit connection
with 1/4 Spade Terminals
Figure 5. Junction box (optional feature)
gland nut
gland gasket
washer
socket head screw
gasket
DIN terminal
connector
connector cover
center screw
adapter
gasket
(see note 1)
DIN connector
terminal block
(see note 2)
Indicates that these parts are included
Open-Frame Solenoid
in DIN plug connector Kit No. K236034
See
torque chart
above
with DIN Terminal
Plug Connector
Notes:
1. Connector cover may be
position shown for alternate
position of cable entry.
2. Refer to markings on DIN
connector for proper
electrical connections.
rotated in 90 increments from
(5/32 hex key wrench)
Figure 6. DIN plug connector kit No. K236034 (optional feature)
50 Hanover Road, Florham Park, New Jersey 07932 www.ascovalve.com
Page 3 of 4Form No.V6583R7
Torque Chart
Part Name Torque Value in Inch-Pounds Torque Value in Newton-Meters
solenoid base sub-assembly 175 ± 25 19,8± 2,8
valve bonnet (3/4 bonnet construction) 90 ± 10 10,2 ± 1,1
bonnet screw (3/8 or 1/2 NPT pipe size)
25 2,8
bonnet screw (3/4 NPT pipe size)
40 4,5
nameplate/
wave
valve
bonnet
plugnut/core tube
sub-assembly
core
(AC) (DC)
solenoid base
sub-assembly
0.9375-26 UNS -2A
thread
core
red cap
Tapped hole in core
0.250-28 UNF-2B
0.38 minimum full thread.
For special wrench
adapter order kit
No. K218948
3/4 Bonnet Construction
15/16 Bonnet Construction
0.750-28 UN-2A
thread
core
Then pry here to lift
nameplate/retainer
gasket
bonnet
washer
Alternate
Construction
retainer
Remove red cap and
push solenoid down.
Then pry here to lift
nameplate/retainer
Remove red cap and
push solenoid down.
and push to remove.
and push to remove.
finger
washer
spring washer
solenoid
with 1/2 NPT
grounding wire -
green or green with
yellow stripes
collar to face
valve body
Side View
Figure 1. Series 8016G solenoids
nameplate/retainer
red cap
solenoid base
sub-assembly
core
retainer
0.69 diameter
mounting hole
.062 to .093 maximum
thickness of panel
for mounting
plugnut/core tube
sub-assembly
core
1.312 diameter
mounting hole
For special wrench
adapter order kit
No. K218948
3/4 Bonnet Construction
15/16 Bonnet Construction
solenoid with 1/2 NPT
spring
valve
bonnet
gasket
bonnet
washer
red cap
nameplate/
retainer
spacer
finger
washer
valve
bonnet
core
tube
solenoid
Then pry here to lift
nameplate/retainer
Remove red cap and
push solenoid down.
Bolted Bonnet
Construction
See torque chart
for bonnet screws
and push to remove.
finger washer
grounding wire -
green or green with
yellow stripes
Figure 2. Series 8016G solenoid Figure 3. Series 8016G panel mounted solenoids
To Next Page
Loading...