Acer AT310 F2 - Motherboard Placement and Jumper Setting; Motherboard Component

85 pages

To Next Page

To Previous Page

Motherboard Placement and Jumper Setting

Motherboard

Component

This section provides general information on changing jumper settings as well as specific jumper

configuration for individual boards in the system.

Main Page

Revision History2
Disclaimer2
Conventions3
Safety, Care and Regulatory Information4
Preventing Electrostatic Discharge4
Server Warnings and Cautions4
Table of Contents5
Mechanical Components9
System Components12
System Specifications13
Hardware Specification13
Environmental Specification17
Mechanical Specification18
Power Supply Specification19
Appearance of System21
Front View21
Rear View22
Internal Component23
Switch and LED Indicators Introduction24
Front Panel LED Description24
LAN Port LED Description25
Hard Disk Drive Sequence & LED Description25
System Block Diagram26
Motherboard Placement and Jumper Setting27
Motherboard Component27
Connector Description and Jumper Setting28
Installing/Removing System Hardware30
Chassis Cover Removal and Installation31
- Removing the Top Cover31
CPU Installation / Removal32
Cooling Fan Installation / Removal33
Memory Installation / Removal34
PCI Expansion Card Installation / Removal35
- Install the Expansion Card35
Hard Disk Drive Installation / Removal36
Power Supply Installation / Removal37
- Install a Fix Power Supply Module37
- Install a Hot-Swap Power Supply Module37
Cable Routing39
Cable Routing Image39
Bios Setup40
- Server Management41
- Boot Options41
- Boot Manager41
Main Menu42
Advanced Menu43
- Processor Configuration44
- Memory Configuration46
- Chipset Configuration47
- ACPI Settings47
- SATA/SAS Configuration49
- PCI Configuration51
- USB Configuration52
- Legacy Device Configuration53
- Power Configuration54
- Console Redirection55
Security Menu57
- Setting a System Password59
- Changing a System Password59
- Removing a System Password59
Server Management Menu60
- System Information61
- Event Log Configuration62
Boot Options Menu64
Boot Manager Menu65
Exit Menu66
Raid Configuration Utilities67
Intel Platform RAID Configuration67
Set RAID Controller in Legacy Mode67
Enabling Intel Onboard SATA RAID67
Entering Intel Onboard SATA RAID BIOS Utility67
Loading Factory Default Setting67
Creating a RAID Volume68
Initializing a RAID Volume68
Assigning a Hot Spare Drive68
LSI Onboard SATA RAID Configuration68
Set RAID Controller in Legacy Mode68
Enabling LSI Onboard SATA RAID68
Entering LSI Onboard SATA RAID BIOS Utility69
Loading Factory Default Setting69
Creating a RAID Volume69
Initializing a RAID Volume69
Assigning a Hot Spare Drive70
Saving and Exiting Onboard RAID Configuration Utility70
Megaraid SAS 9240-4I / 9260-8I RAID Configuration70
Set RAID Controller in EFI Mode or Legacy Mode70
Entering RAID BIOS Utility (Legacy Mode)70
Creating a RAID Volume71
Initializing a RAID Volume71
Entering RAID EFI Utility (EFI Mode)71
Loading Factory Default Setting71
Assigning a Hot Spare Drive72
3041E-R RAID Configuration72
Set RAID Controller in Legacy Mode72
Entering RAID BIOS Utility72
Loading Factory Default Setting72
Creating a RAID Volume72
Initializing a RAID Volume73
Assigning a Hot Spare Drive73
Troubleshooting74
Error Symptoms List74
BMC Event and Ikvm Event Troubleshooting77
Bios Beep Codes79
BIOS Beep Codes Table79
- PEI Beep Codes79
- DXE Beep Codes79
BIOS Recovery Instruction80
Bios Post Error Messages List82
BIOS POST Error Message List82
- PEI Phase82
- DXE Phase83
Undetermined Problems85

Acer AT310 F2 - Motherboard Placement and Jumper Setting; Motherboard Component

Table of Contents

Other manuals for Acer AT310 F2

Related product manuals