ActronControls Leasam BM2-7D-4Z User Manual

ON
OFF
FAN
CONTROL
1
MID
HIGH
CONT
TUE WED THUR FRIMON
SAT
SUN
SET
AM
PM
COOL
23.0
EVENT 12
TIME CLOCK
TIMECLOCK
PROGRAM
REPEAT
TEMP
EXIT
SET
ON
LOW
OFF ROOM
COOL HEATAUTO RUN TIMER FILTER
AUTO HEAT
REPEAT
TIMER
1
3
LIVING
OFFICE
2
FAMILY
4
BEDROOMS
Page
2
BM2 7D 4Z/GP Operating Instructions
ON
OFF
Press to START or STOP the Air Conditioner
Press to select COOLING ONLY operation
Press to select AUTO operating mode.
1
2
3
4
5
6
7
8
9
10
1
2
3
4
5
6
COOL
AUTO
The system automatically selects HEATING or COOLING on demand
Press to select HEATING ONLY operationHEAT
Press to activate the COUNTDOWN TIMER
TIMER
If the system is ON, it turns OFF after the set period (e.g. sleep timer)
If the system is OFF, it turns ON after the set period (adjust 30 min - 24 Hr)
After pressing (while the TIMER light is flashing)TIMER
7
Mode lights indicate the system operating status
e.g. "RUN" light indicates the compressor is running.
Press TIMER to adjust the TIMER duration
or
DPO-BM27DOP-1 Sub
j
ect to chan
g
e without notice. E&OE. AUG 2008
Page
3
8
9
10
CONTROL
FAN
Keep pressing to cycle through the fan speeds
HIGH, MID, LOW, CONT HIGH, CONT MID, CONT LOW - CONT is Continuous
"CONTINUOUS" air circulation is usually used in COOLING.
Press or to adjust the SET POINT
SET
TEMP
to the room temperature you desire usually ~ 22.5
Zone selection (option) allows comfort control of specific areas
The zone lights indicate the active areas in the house, one zone always remains on.
Zone selection increases the efficiency of your Air Conditioner and saves energy
LOCK THE SET POINT RANGE to resist tampering
UPPER LIMIT
- Press TIMER then (default is 28)
to turn off
the system
SET
TEMP
While it is flashing , to set the limits.
or
or
SET
TEMP
Press
FILTER LIGHT FLASHING
This is a warning after 160 hours of running time, to remind you to check
the RETURN AIR FILTER to see if it needs a clean. To reset : Press
ON
ON
OFF
OFF
DISPLAY ROOM TEMPERATURE
"Quick Press" TIMER to check the room temperature ( "ROOM" light flashes )
The room temperature is displayed for 3 seconds, then the display reverts back to set point
VENTILATION MODE
With the system off, Press to circulate the air.
CONTROL
FAN
ON
OFF
Press to stop fan
LOWER LIMIT
- Press TIMER then (default is 16)
SET
TEMP
While it is flashing , to set the limits.
SET
TEMP
Press
Press
DPO-BM27DOP-1 Sub
j
ect to chan
g
e without notice. E&OE. AUG 2008

ActronControls Leasam BM2-7D-4Z Specifications

General

Brand	ActronControls
Model	Leasam BM2-7D-4Z
Category	Control Systems
Language	English

Summary

Basic Air Conditioner Operation

Power and Mode Selection

Control system power and select between cooling, auto, or heating modes for operation.

Timer and Temperature Adjustments

Set countdown timers and adjust desired room temperature set points.

Fan Speed and Zone Control

Select fan speed and manage comfort control for specific areas.

System Status and Warnings

Understand mode lights, filter warnings, and view room temperature.

Ventilation Mode

Circulate air without activating heating or cooling.

7-Day Time Clock Programming

Timeclock Setup and Control

Activate, deactivate, set the current time, and day for the timeclock.

Programming Daily Events

Set up to two ON and OFF events per day for automated control.

Event Management

Repeat previous day's settings or delete programmed events.

Past Midnight Events

Schedule events that extend past midnight into the next day.