ADTEK CPM-10 - Page 18

a d v n c
p r o g
B-10
r ! # s p
4 % 0 0
B-9
r ! # m d
o f f
B-8
r ! # s l
f r e q
B-7
r ! @ s p
2 % 0 0
B-6
r ! @ m d
l o
B-5
r ! @ s l
I a v g
B-4
r ! ! s p
3 ) 0 0
B-3
r ! ! m d
o f f
B-2
1 /7 24
Engineer level( )Raely Output
■Operating Steps
Enter
DecreaseIncrease
Shift
Relay R1.1
Setting type:
L O H I LO .H LD H I. HL D/ / / /
O F F
l o：PV Setpoint relay energized＜ ， 。
h i：PV Setpoint relay energized＞ ， 。
l o. h l d：Display Setpoint relay energized＜ ， ,
and hold energized status。
h i. h l d：Display Setpoint relay energized＞ ， ,
and hold energized status。
o ff：Close relay function when relay is off,,
relay remain open, LED will not light。
Press values blink press change value or selection, , &
when done press secto next setting or hold 1 .
to previous selection list
Enter
DecreaseIncrease
Shift
Parameters Display Setting Operation
Relay R1.1 value
setting:
Setting range:
-199.99~29 .999
Press values blink press change value or selection, , &
when done press secto next setting or hold 1 .
to previous selection list
Relay R Mode1.2 :
Relay R setting type1.2
: 1.1same R
Press values blink press change value or selection, , &
when done press secto next setting or hold 1 .
to previous selection list
Relay R1.2 Mode:
Setting type:
L O H I LO .H LD H I. HL D/ / / /
O F F
Press values blink press change value or selection, , &
when done press secto next setting or hold 1 .
to previous selection list
Relay R1.2 value
setting:
Setting range:
-199.99 299.9~ 9
Press values blink press change value or selection, , &
when done press secto next setting or hold 1 .
to previous selection list
Relay R Mode1.3 :
Relay R setting type same1.3 :
R1.1
Press values blink press change value or selection, , &
when done press secto next setting or hold 1 .
to previous selection list
Relay R1.3 Mode:
Setting type:
L O H I LO .H LD H I. HL D/ / / /
O F F
Press values blink press change value or selection, , &
when done press secto next setting or hold 1 .
to previous selection list
Relay R1.3 value
setting:
Setting range:
-199.99~2 .9999
Press values blink press change value or selection, , &
when done press secto next setting or hold 1 .
to previous selection list
Program selection:
prog Programming for basic(
or advance setting ):
Enter
DecreaseIncrease
Shift
In parameters setting level, default is basic during setting it， ,
only show common functions,advance functions is hidden.User
can change setting in each group , set it[ ]p r o g
a d v n c( )advance to show all functions.
En d te rm in al o hm
ADEFGHI -1,:JKL)*MNO.PQNOMRS.<)
*3 4RSTUVWP4W.3
)*1 2 4,1-10~1-27XYZRSP W
)*1 4,1-14/1-1 ~ XYZRSP3W 6 27
)*3 4,1-1 1-1 /1-1 1- /P3W.1 3~ 5 7/1-18/ 20 1-21/1-23/1-24/1-
26/1-27XYZRS
)*3 4,1-1 1- /1- XYZRSP3W.2 7/ 20 23/1-26
)*3 4,1-1 1- /1- XYZRSP3W.3 7/ 20 23/1-26
)*3 4,1-1 1- /1-P4W.1 4~15/ 17~18 20~21/1-23~24/1-26~27
XYZRS
)*+,:1 p 2 w 1 p 3 w 3 p 3 w .1 3 p 3w .2 3p 3w .3/ / / / /
3 p 4 w .1 3 p 4 w .3/
"#$%&':
v a v g. ()*+,-.:
i a v g. ()*/,-.:
f r e q :
2345.
p . t l :()673.
q . t l :()6873.
s . t l :()69:73.
p f . a vg :(),-73;
%45.
v a : )*+.45A
vb :B)*+.45
vc :C)*+.45
ia :A)*/.45
ib :B)*/.45
ic :C)*/.45
p f - a :A)7345.
pf-b :B)7345.
pf-c :C)7345.
p - a :A)7345.
p-b :B)7345.
p-c :C)7345.
q - a :A)87345.
q-b :B)87345.
q-c :C)87345.
s - a :A)9:7345
s - b :B)9:7345
s - c :C)9:7345
RELAY / PULSE output of the outputs can
only choose a functional output
EX: Select PULSE output and then RELAY
function no output and vice versa
Clamp CT
Optional of Clamp CT, make sure
(1)CT of the SN number with the
CPM-10 SN number, as shown
( )2 On the label
A A Phase B B: - ; : -
Phase C C Phase; : - ;
According to the phase matching
Relay Pulse output
CL
BK
AK
AL
BL
CK
, ,0123CT4 56789:; <=>?@A