AEG BSS18C12ZB6 - Page 14

14
14
BATTERY AND CHARGER
Compatible battery pack
(not included)
Compatible charger
(not included)
L1815R
L1820R
L1825R
L1830R
L1840R
L1850R
L1860R
L1860B
L1860R-X5
L1890R
AL18G
AL1218G
BL1218
BLK1218
BL18DP-X5
BL18DP2-X5
BL18DPS
Use AEG 18V battery and charger only
WARNING! Read all safety warnings, instructions, illustrations and
specifications provided with this power tool. Failure to follow all instructions
listed below may result in electric shock, fire and/or serious injury. Save all
warnings and instructions for future reference.
IMPACT WRENCH SAFETY WARNINGS
Hold the power tool by insulated gripping surfaces, when performing
an operation where the fastener may contact hidden wiring. Fasteners
contacting a “live” wire may make exposed metal parts of the power tool “live”
and could give the operator an electric shock.
Wear ear protectors. Exposure to noise can cause hearing loss.
Sawdust and splinters must not be removed while the machine is running.
When working in walls, ceiling, or floor, take care to avoid electric cables and
gas or waterpipes.
Remove the battery pack before starting any work on the machine.
Do not dispose of used battery packs in the household refuse or by
burning them. AEG Distributors oer to retrieve old batteries to protect our
environment.
Do not store the battery pack together with metal objects (short circuit
risk).
Use only System AEG chargers for charging System AEG battery packs. Do
not use battery packs from other systems.
Battery acid may leak from damaged batteries under extreme load or
extreme temperatures. In case of contact with battery acid wash it o
immediately with soap and water. In case of eye contact rinse thoroughly for
at least 10 minutes and immediately seek medical attention.
ADDITIONAL SAFETY WARNINGS
Ambient temperature range for tool during operation is between 0°C and 40°C.
Ambient temperature range for tool storage is between 0°C and 40°C.
The recommended ambient temperature range for the charging system during
charging is between 10°C and 38°C.
RESIDUAL RISKS
Even when the product is used as prescribed, it is still impossible to completely
eliminate certain residual risk factors. The operator should pay particular and
additional attention to these points in order to reduce the risk of serious personal
injury.
■ Injury to hearing – Wear suitable ear protection and limit exposure.
■ Injury to sight – Wear protective eye shields or goggles when using the
product.
■ Injury caused by vibration – Limit exposure and follow the instructions on
risk reduction in this manual.
■ Electric shock after contact with hidden wires – Hold the product only by
insulated surfaces.
TECHNICAL DATA 18V BRUSHLESS IMPACT WRENCH
BSS18C12ZB6
Rated voltage 18 V
Tool reception 1/2” (12.7 mm)
No-load speed 0 - 3000 min
-1
Impact rate 0 - 4000 min
-1
Max torque 300 Nm
Max. diameter bolt / nut M14
Weight - not including battery pack 1.17 kg
Measured values determined according to EN 60745.
A-weighted sound pressure level L
p
= 99.5 dB(A)
Uncertainty K 3 dB(A)
A-weighted sound power level L
W
= 110.5 dB(A)
Uncertainty K 3 dB(A)
Wear ear protectors.
The vibration total values (triaxial vector sum) determined according to EN 60745:
Impact tightening of fasteners of the maximum capacity of the tool a
h
= 6.7 m/s
2
Uncertainty K 1.5 m/s
2
WARNING
The vibration emission level given in this information sheet has been measured in accordance with a standardised test given in EN 60745 and may be used to compare
one tool with another. It may be used for a preliminary assessment of exposure. The declared vibration emission level represents the main applications of the tool.
However if the tool is used for dierent applications, with dierent accessories or poorly maintained, the vibration emission may dier. This may significantly increase
the exposure level over the total working period.
An estimation of the level of exposure to vibration should also take into account the times when the tool is switched o or when it is running but not actually doing
the job. This may significantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from the eects of vibration such as: maintain the tool and the accessories, keep the hands warm,
organisation of work patterns.