AEG OMNI 18C-PB - User Manual

Need help?

Do you have a question about the AEG OMNI 18C-PB and is the answer not in the manual?

Overview

Function Description
Important Technical Specifications
Noise Information (Measured according to EN 60 745)
Usage Features
Safety Instructions
Specified Conditions of Use
Maintenance Features
Environmental Protection

This document serves as the original instructions manual for the AEG OMNI 18C-PB Powerbase, a component of the AEG POWERTOOLS system. The manual emphasizes the importance of reading the instructions before operating the machine and notes that the product is subject to technical modifications.

Function Description

The AEG OMNI 18C-PB is a powerbase designed to drive various approved application heads of the AEG brand. It is a cordless power tool, indicated by its 18V battery voltage. The powerbase itself does not perform a specific task but provides the power and control for different application heads, allowing for a versatile range of functions depending on the attached head. The overview on page 3 illustrates several compatible application heads, including OMNI-RAD, OMNI-IH, OMNI-IR, OMNI-MT, OMNI-RH, and OMNI-JS, which can be purchased separately. The powerbase is designed to be operated only with a mounted application head, and these heads can be positioned in three different orientations on the powerbase.

Important Technical Specifications

Model: OMNI 18C-PB
Battery voltage: 18 V
No-load speed: 20000 min⁻¹
Weight (according to EPTA-Procedure 01/2003): 545 g

Noise Information (Measured according to EN 60 745):

Sound pressure level (K=3dB(A)): 93 dB (A)
Sound power level (K=3dB(A)): 104 dB (A)
Recommendation: Wear ear protectors.

Usage Features

The manual provides clear visual instructions for operating the OMNI 18C-PB powerbase.

Battery Installation and Removal:
- To install the battery pack, slide it into the powerbase until it clicks into place (pages 4-5).
- To remove the battery pack, press the release buttons on the sides of the battery and slide it out.
- Safety Precaution: Always remove the battery pack before starting any work on the machine.
Application Head Installation and Removal:
- To install an application head, align it with the powerbase and push it in until it clicks (page 6). The application head can be installed in three different positions (page 7).
- To remove an application head, press the release button on the powerbase and pull the head off.
- Safety Precaution: Remove the battery pack before attaching or detaching application heads.
Operation (Start/Stop):
- The powerbase features a trigger for starting and stopping the tool (page 8).
- The tool also includes a speed control feature, allowing adjustment between slower (turtle icon) and faster (rabbit icon) operation.
- Safety Precaution: Ensure the powerbase is locked when not in use to prevent accidental startup.
Locking Mechanism:
- The powerbase has a locking mechanism to prevent unintentional activation (page 9).
- To lock, push the lock button forward. To unlock, pull the lock button backward.
Integrated LED Light:
- The powerbase is equipped with an LED light to illuminate the work area (page 10). This feature enhances visibility during operation, especially in dimly lit conditions.

Safety Instructions

The manual includes a comprehensive list of safety instructions:

Personal Protective Equipment: Wear ear protectors due to noise exposure, goggles, gloves, sturdy non-slipping shoes, and an apron.
Dust Protection: The dust produced can be harmful. Use a dust absorption system and a suitable dust protection mask. Remove deposited dust thoroughly with a vacuum cleaner.
Electrical Safety: Hold the power tool by insulated gripping surfaces when performing operations where the cutting accessory may contact hidden wiring to avoid electric shock.
Work Area Safety: When working in walls, ceilings, or floors, take care to avoid electric cables and gas or water pipes.
Tool Handling: Sawdust and splinters must not be removed while the machine is running.
Battery Safety:
- Remove the battery pack before starting any work on the machine.
- Do not dispose of used battery packs in household refuse or by burning them. AEG Distributors offer to retrieve old batteries for environmental protection.
- Do not store the battery pack with metal objects to prevent short circuit risk.
- Use only System PCLS chargers for charging System PCLS battery packs. Do not use battery packs from other systems.
- In case of battery acid leakage (from damaged batteries under extreme load or temperatures), wash off immediately with soap and water. If eye contact occurs, rinse thoroughly for at least 10 minutes and seek medical attention.

Specified Conditions of Use

This powerbase is designed to drive approved application heads of the AEG brand.
Do not use this product in any other way as stated for normal use.

Maintenance Features

Battery Care:
- New battery packs reach full loading capacity after 4-5 chargings and dischargings.
- Recharge battery packs that have not been used for some time before use.
- Avoid temperatures exceeding 50°C (122°F) to prevent reduced performance and overheating.
- Keep contacts of chargers and battery packs clean.
- For optimum life-time, fully charge battery packs after use.
- Remove the battery pack from the charger once it is fully charged to obtain the longest possible battery life.
- For storage longer than 30 days, store the battery pack below 27°C and away from moisture, in a 30%-50% charged condition.
- Charge the pack as normal every six months of storage.
Battery Pack Protection: The battery pack has overload protection. Under extreme stress, the battery electronics will automatically switch off the machine. To restart, switch the machine off and then on again. If it does not start up, the battery pack may be completely discharged and needs recharging.
General Maintenance:
- Use only AEG accessories and spare parts.
- For replacement components not described in the manual, contact an AEG service agent.
- An exploded view of the tool can be ordered by stating the Article No. and machine type to a local service agent or directly from Techtronic Industries GmbH, Max-Eyth-Straße 10, D-71364 Winnenden, Germany.

Environmental Protection

Do not dispose of electric tools with household waste.
In observance of European Directive 2002/96/EC, waste electrical and electronic equipment must be collected separately and returned to an environmentally compatible recycling facility.