AGCO LELY RPC 130 F User Manual

3.4.7 Set the Correct Number of Knives .................................... 92
3.4.8 Prepare the Wrapper for Operation ................................... 92
3.4.9 Insert a New Film Roll ............................................ 93
3.4.10 Operating Position of the Bale Mat (optional) ............................ 94
3.4.11 Operating Position of the Bale Tipper (optional) .......................... 95
3.4.12 Adjust the Bale Tipper ............................................ 96
3.4.13
Adjust the Machine Settings on the Controller ........................... 96
3.4.14 Open or Close the Side Covers ...................................... 97
3.5 To Operate the Machine ............................................. 98
3.5.1 Check Before You Operate the Machine ............................... 98
3.5.2
Start Baling and Wrapping ..........................................98
3.5.3
Make Two or Three Smaller Bales at the End of the Field
................... 99
3.5.4 Make One Larger Bale at the End of the Field ........................... 99
3.5.5 Drive Instructions for Material Intake .................................. 99
3.5.6 Large Swath ................................................... 99
3.5.7 Small Swath ....................................................99
3.5.8 Drive on Slopes ................................................ 101
3.5.9 Dry, Brittle, Smooth Crop Material ................................... 101
3.5.10 Transfer a Bale ................................................. 101
3.5.11 Eject a Bale from the Wrapper ...................................... 102
3.5.12 Remove a Blockage ............................................. 102
3.5.13
Shut Down Procedure on the Field .................................. 103
3.6 Disconnect the Machine from the Tractor ............................ 105
3.6.1 Park the Machine ............................................... 105
3.6.2 Remove the Pressure from the Hydraulic System ........................ 105
3.6.3 Disconnect the Machine .......................................... 105
3.6.4 Support Foot .................................................. 106
3.6.5 Install the Support Foot ........................................... 107
3.6.6 Remove the Support Foot ......................................... 107
3.6.7 To Move the Machine without Brakes ................................ 108
3.6.8 Take the Machine out of Operation .................................. 109
4 Maintenance and Lubrication ............................................. 111
4.1 Preventative Maintenance Schedule ................................. 113
4.2 Lubrication Chart ................................................... 115
4.3 Clean the Machine ..................................................119
4.4 Chain Lubrication System Maintenance .............................. 120
4.4.1 Check the Level in the Oil Container of the Chain Lubrication ............... 120
4.4.2 Fill the Oil Container ............................................. 120
4.4.3 Bleed Air from the Lubrication Pump ................................. 121
4.5 Roller Lubrication System Maintenance (RPC 130 F only) ............. 123
4.6 Tighten the Chains of the Pick-Up, Bale Chamber and Feed Rotor ......124
4.7 Tighten the Chains of the Wrapper .................................. 126
4.8 Examine the Hydraulic Oil Filter ..................................... 127
4.9 Replace the Hydraulic Oil Filter ...................................... 128
4.10 Examine the Hydraulic Hoses for Damage and Leaks .................. 129
4.11 Grind the Cutting Unit Knives ....................................... 130
4.11.1 Remove the Knives .............................................. 130
4.11.2 Grind the Knives ................................................ 131
4.11.3 Install the Knives ............................................... 131
4.12 Replace the Knives with Blind Knives ................................ 132
4.12.1 Remove the Knives .............................................. 132
4.12.2 Install the Blind Knives ........................................... 133
4.13 Replace the Film Knives ............................................ 134
4.14 Adjust and Replace the Belt Guide Pulleys ........................... 135
Table of contents
Baler Wrapper Combination
4900.LE.EN01

AGCO LELY RPC 130 F Specifications

General

Brand	AGCO
Model	LELY RPC 130 F
Category	Industrial Equipment
Language	English