Need help?Do you have a question about the Agrimate AM-6600-9P and is the answer not in the manual?
Covers the cylinder head assembly.
Seals the cylinder head cover.
Fasteners used for assembly.
Threaded fasteners for secure connections.
Standard fastening bolt.
Provides cushioning for bolts.
Ignition component for the engine.
Main component of the engine's cylinder head.
Alignment pins for precise component fitting.
Seals the cylinder head to the engine block.
Protects components from debris or airflow.
Main housing for the crankshaft and bearings.
Component of the engine's governor system.
Secures the governor arm shaft.
Seals to prevent oil leakage in the speed control system.
Component that reduces friction for rotating parts.
Fastener for assembling the crankcase.
Pad made of aluminum, possibly for mounting or vibration damping.
Gasket made of rubber for sealing.
Seal to prevent oil leakage.
The cover for the crankcase.
Seal to prevent oil leakage.
Bolt with a hex head and flange for secure fastening.
Assembly for checking engine oil level.
Ring to seal the dipstick.
Assembly for adding oil to the engine.
Gasket for the crankcase cover.
Pins used for alignment of components.
Component that supports rotating shafts.
Complete kit for the engine governor system.
Assembly of the crankshaft.
Key used to lock components onto shafts.
Bearing for the crankshaft.
Assembly connecting piston to crankshaft.
Retaining clip for the piston pin.
Pin connecting piston and connecting rod.
Component that moves within the cylinder.
Set of rings for the piston.
First gas ring for the piston.
Second gas ring for the piston.
A loop or ring, possibly for sealing or retaining.
A ring-shaped bearing or bushing.
Assembly that operates the valves.
Component that lifts the valve.
Rod transmitting force from lifter to rocker.
Valve that allows fuel/air mixture into the cylinder.
Valve that allows exhaust gases out of the cylinder.
Component holding the valve spring.
Seal for the valve stem.
Spring that closes the valve.
Seat for the exhaust valve spring.
Adjuster for the exhaust valve.
Guide for the push rod.
Rocker arm assembly.
Pivot bolt for the rocker arm.
Rocker arm component.
Nut for adjusting valve clearance.
Locking nut for the pivot.
Complete assembly for the recoil starter.
Component to direct airflow, possibly for cooling.
Fasteners for the recoil starter assembly.
Assembly for the engine stop switch.
Plug related to the recoil starter.
Main component of the recoil starter.
Bolt that centers a component.
Guide for the ratchet mechanism.
Spring that centers a component.
Ratchet mechanism for the starter.
Spring that returns a component.
Reel component of the recoil starter.
Spring for returning the starter mechanism.
Cover assembly for the recoil starter.
Rope for the recoil starter.
Handle for operating the starter.
Main casing for the recoil starter assembly.
Clamp for securing wires on the starter.
Washer for the air intake system.
Component providing electrical or thermal insulation.
Seal or gasket for the carburetor.
Device that mixes air and fuel.
Gasket for the air cleaner.
Assembly for filtering intake air.
Nut for the inlet assembly.
Fastener for the inlet assembly.
Complete air cleaner assembly.
Housing for the air filter element.
Pipe for handling waste gases.
Sealing material for the air filter.
Cup for oil in the air filter system.
Sponge element for the air cleaner.
Foam element for air filtration.
Cover with sealing properties.
Nut with wing-like projections for manual tightening.
Cover for the air cleaner.
Wheel operated by hand, likely for adjustment or securing.
Main component mixing fuel and air.
Cap for the idle fuel passage.
Component related to the idle circuit.
Set of jets for the pilot circuit.
Handle to operate the choke plate.
Fastener for carburetor components.
Cover plate for the fuel switch.
Washer for carburetor fasteners.
Handle for the fuel shut-off switch.
Seal for the fuel shut-off switch.
Pin used in carburetor assembly.
Main fuel nozzle.
Main jet for fuel delivery.
Assembly of float and needle valve.
Float chamber assembly.
Washer for float chamber fasteners.
Gasket for the carburetor.
Fastener for carburetor components.
Bolt that also acts as a drain plug.
Complete throttle control assembly.
Fastener for the throttle control.
Arm component of the governor linkage.
Bolt with a T-shaped head.
Nut for the throttle control assembly.
Connecting rod or linkage.
Spring for fine adjustment of throttle.
Spring that controls engine speed via governor.
Ignition system component.
Cap for the ignition system.
Cord for the engine stop switch.
Fastener for the ignition system.
Rotating mass that stores kinetic energy.
Fan for engine cooling.
Pulley involved in the starting mechanism.
Nut for the flywheel assembly.
Complete muffler assembly.
Gasket for the muffler.
Exhaust pipe assembly.
Washer for the exhaust system.
Nut for the exhaust assembly.
Washer that provides spring tension.
Cover providing guidance or protection.
Fastener for the exhaust assembly.
Complete fuel tank assembly.
Assembly for the fuel filler cap.
Seal for the fuel filler.
Component to filter fuel.
The main container for fuel.
Sealing component for the fuel tank.
Connection point for the fuel tank.
Clip to secure a fuel tube.
Hose for fuel transfer.
Fastener for the fuel tank assembly.
Washer for fuel tank fasteners.
Nut for the fuel tank assembly.
Rubber gasket for the fuel tank.
Clamp for securing fuel lines.
To Next Page
General