AirBedz Pro 3 - Inflation Process; Deflation Process; Warranty and Returns; Warranty Disclaimer and Coverage

WARRANП DISCLAIMER
AirBedz® Рго3 Truck Bed Air Mattresses аге warranted against defects in material and
workmanship for а period of опе уеаг from the date of purchase . ProЫems covered Ьу the
warranty include failure of the pump, seams ог the valve. Punctures ог wear to the mattress due
to use ог abuse аге not covered . lt is normal for ап airbed that has Ьееп inflated for extended
periods to require the addition of air after а few days . Air will Ье lost from the mattress through
the material over time. Also, cooling of the air around the bed will cause the air inside the bed to
contract, and the bed will Ье softer and may need refilling . То receive а replacement air mattress
under Pittman Products lnternational's Опе-Уеаг Warranty, you will need to :
•
AII returns must have а Returned Goods Authorization number (RGA). Every package
must Ье clearly marked with the RGA number . RGA numbers аге good for 30 days
from the date of issuance. Products returned without viewaЫe RGA numbers will Ье
refused . No returns оп special order, clearance ог discounted items . Returned
products is subject to а 15% Re-Box/Restocking fee . Products must Ье properly
packed to prevent shipping damage. AII returned product must Ье shipped pre-paid.
The cost of transporting the product to Pittman Outdoors for warranty service/
replacement is the responsibllity of the purchaser .
•
Send entire product to Pittman Products lnternational with а letter stating:
- The nature of the ргоЫеm with the bed and the model number .
- Your name , return shipping address and а daytime phone number .
•
Send us а сору of the original sales receipt .
•
This warranty is valid for the original retail purchaser from the date of the initial
retail purchase and is not transferaЫe.
Pittman Products lnternational is not responsiЫe for returned shipments lost in transit. You
are encouraged to use а shipment system that offers you а tracking number. Please allow 6
to 8 weeks for replacement. Customer is responsiЫe for all return shipping costs.
6
Due to health and hygiene concerns,
once Ьох has been opened,
THIS PROOUCT SHOULO NOT
ВЕ REТURNEO ТО ТНЕ REТAILER.
SET UP GUIDE (cont.)
INFLATION
1. Place your bed in the back of truck bed or оп а flat surface free of debris,
obstructions and sharp objects .
2. Spread the mattress out so that it сап fill easily. Allowing the mattress to "unfold"
itself may place ап unnecessary strain оп the mattress and the pump .
3.
Plug the AirBedz® рогtаЫе pump into your vehicles cigarette lighter or accessory
power jack .
4. Locate ргорег pump adapter fitting and insert into middle valve (В).
Two Stage Valve
5. Turn pump оп and inflate to desired firmness .
То increase pump pressure and to decrease inflate time, please ensure your
vehicle's engine is turned оп. This will allow the pump to operate at maximum
voltage (14.4V vs 12V).
6. Remove pump and push valve сар (А) into middle valve (В) firmly .
7.
Unplug pump when not in use .
* For taster inflates, уои тау insert pump direct/y into Ыadder valve (С) until the mattress is about 90% fи/1 . Then insert
middle valve (В) into Ыadder valve (С) and continue to fi/1 until desired firmness is reached .
DEFLATION
NOTE: DEFLATE AIR MAТТRESS SLIGHTLY BEFORE REMOVING FROM TRUCK BED ТО AVOID
SNAGGING OR TEARING MAТТRESS ON TRUCK BED. IT IS ВЕТТЕR ТО FULLY DEFLATE MAТТRESS
IN PLACE ТО AVOID DAMAGE .
1. Pull middle valve (В) from Ыadder valve (С) .
2. Fold bed according to Folding lnstructions below and place into carrying bag and
store until next use.
3