Aiwa HS-PL10 - Page 2

DISASSEMBLY INSTRUCTIONS
L. Wveyr ERY bhOUF UA (Fig-1B)
1) EASA(MO DO ODOD)&LAFL. KHOOAMKK RAN
AWERSTT.
EAA) X1+++++Special screw V+1.4-2.5
EK AG) Xl+++**Special screw V+1.4-1.4
KAO X 210+ V41.4-3
EK AC) X1s++ Special screw V+1.4-2.5
2) KA3A(O) ©) RUF L. KHODAMIKU -V Fy ER
yhRIGSS.
FAQ) Xdeeree Special screw V+1.4-2.5
EAE) X levees KARYA—Fee
1. Rear Cabinet Removal (See Fig.1)
1) Remove 5 screws (A@),@), ©and@)) and take
out the bottom panel in the direction of arrow @.
Screw (A) X 1 *** Special screw V+1.4-2.5
Screw(B) X Leis
Screw (C) X 2 ee* V41.4-3
Screw(D) X 1 +++ Special screw V+1.4-2.5
2) Remove 3 screws (@),®) and take out the rear
cabinet in the direction of arrow @.
Screw (’) X2 +++ Special screws ¥+1.4-2.5
Screw(E) X1 *+* Center cabinet screw
re?
KR AANA
Bottom panel
Special screw ¥+1,4-1.4
Yvert Ry hk
Cabinet, Rear
Fig.1
2. BYR—-FV-ADIUF LA (Fig-28M)
1) EA2ZK(M@) EY FRAT L. KAOOAMK EY
I—-JV-ARUFT.
EK A® X1++++*Special screw V+1.4-2.5
EK AG X1++++Special screw ¥+1,4-3.5
2. Center Frame Removal (See Fig. 2)
1) Remove 2. screws (®,@) and five knobs and take
out the center- frame in the direction of arrow @.
Screw(F) X 1 +++ Special screw V+1.4~2.5
Screw@)X 1 °*+ Special screw V+1.4-3.5
IJFABAK
Knob, Slide i
ByaA-IV-LA
Center frame
Do not remove 3
Fig.2
this screy. Main C.B
3. AA VERORIUA (Fie 3M)
1) CABAK(D OD) EAL. RHOOAMAS 4 VARS BO
Tv.
CAC) X 2evee V4 4-2.2
CAD Xl CARL—B M14-2
3. Raising (Opening) Main Circuit Board (See Fig.3)
1) Remove 3 screvs ((H),(1)) and raise the main
circuit board in the direction of arrow @.
Screw(H) X 2 +++ V+1.4-2.2
Screw (1) X 1 +++ Serrated screw M1.4-2
a4 VEER
Fig. 3
4, €-H¥—-OWRFUAR (Fie4BM)
(E— 4 — 3S Hs)
1) HEY KSA,
2) HRY bhAY7AMDE AIA(D ©) HL. E-4—-*&
BHANT.
CAG X 2e+2+-Q41.4-1.4
EK A® X leeeeee4-1.6
7E) BRM K ILD TOSRAIE AGRI. MAS
CRA. BEAMIMAY CLEW I 4 ABAOKAKS
DES. (Fig-4R)
4. Motor Removal (Motor Replacement) (See Fig.4)
1) Open the cassette lid.
2) Remove 3 screvs (@,@®) from the cassette box
and take out the motor backwards.
Screw) X 2 +++ Qel.4-1.4
Screw(K) X 1 ++ V#1.4-1.6
Note) Never remove four screws from the circuit board as
this could drift the height adjustment and cause
noise to occur. (See Fig.4)
Main C.B
Fig. 4
ewyuAaA-DV—sA
Center frame
JK GAGA ABE, MACHER ALE LER AV. )
Hook (Insert the CB into the hooks when reinstalling it).