Need help?Do you have a question about the AJA Ki Pro GO and is the answer not in the manual?
General| Brand | AJA |
|---|---|
| Model | Ki Pro GO |
| Category | Measuring Instruments |
| Language | English |
Lists registered and unregistered trademarks of AJA Video Systems, Inc. and other companies.
States the copyright notice and restrictions on document reproduction.
Provides contact methods (telephone, web, email) for AJA sales and support.
General introduction to the AJA Ki Pro GO device and its capabilities.
Lists the key hardware and software features of the AJA Ki Pro GO recorder/player.
Details compatible file systems and formatting guidelines for USB media.
Information on recommended USB media and compatibility for the Ki Pro GO.
Outlines the content and structure of the installation and operation guide.
Overview of the Ki Pro GO's front panel controls, display, and ports.
Details the front panel USB ports and their LED status indicators.
Describes the quad split display and overlays on the Ki Pro GO's LCD.
Explains how to use the DISP button to cycle through video overlay display modes.
Details the function of the User Control Knob for menu navigation and parameter adjustment.
Describes how to access and use the STATUS overlay and alarm indications.
Explains how to access and navigate the CONFIG menu for device settings.
Details how to access and navigate the MEDIA menu for clip and storage management.
Explains the color coding and meaning of the audio VU meters displayed on the LCD.
Configures the FUNC button for quick menu access.
Explains the function of the PLAY, RECORD, STOP, FFWD, and REV buttons.
Details how to turn the Ki Pro GO unit on and off, including power-up behavior.
Describes the headphone jack and how to adjust the listening volume.
Explains the function of the Reference Loop BNC connectors for timing signals.
Details the four 3G-SDI input connectors and their capabilities.
Describes the four 3G-SDI output connectors and their linkage to recording channels.
Details the four HDMI input connectors and their audio/video support.
Describes the SDI monitor output for viewing channel status.
Describes the HDMI monitor output for viewing channel status.
Explains the two XLR connectors for analog audio input.
Details the RCA connectors for analog audio output.
Describes the RJ-45 connector for network connectivity and remote control.
Explains the 4-pin XLR connectors for DC power input.
Introduces the basic setup and remote control options for the Ki Pro GO.
Lists the components included with the Ki Pro GO recorder.
Provides essential cautions for installing the Ki Pro GO unit.
Details the procedure for attaching the optional handle to the Ki Pro GO.
Explains how to connect and use the AC adapter for powering the Ki Pro GO.
Details how to connect and use a DC power source for the Ki Pro GO.
Information on connecting the Ki Pro GO directly to a computer via Ethernet.
Step-by-step guide for establishing a direct connection between Ki Pro GO and a computer.
Explains the need for DHCP or Static IP information from network administrators.
Steps to configure the Ki Pro GO on a network using DHCP.
Steps to configure the Ki Pro GO on a network using a static IP address.
Introduces controlling the Ki Pro GO using its front panel interface.
Explains the information displayed in various menu overlays on the front panel.
Describes the information shown on the front panel display upon power-up.
Details the information presented on the bottom line of the front panel display.
Explains how to view status information via the STATUS button and its tabs.
Describes the Channel/Input status information displayed on the Ki Pro GO.
Details the File/Encode status information for recording channels.
Explains how to view and interpret alarm messages and warnings.
Lists and explains various warning messages related to media and input status.
Describes navigation and interaction within the CONFIG and MEDIA menus.
Guide to recording clips using the Ki Pro GO's front panel controls.
Instructions for routing video and audio sources to recording channels.
Step-by-step process for capturing video and audio clips.
How to set up and record backup clips to a separate USB port.
Information on media capacity alerts and management for recording.
Guide to playing back recorded clips using the front panel.
Steps to select, cue, and initiate playback of a specific clip.
How to configure playback for single clips or all clips on the media.
How to set clips to play continuously or stop after one playback.
Overview of the configuration menus for device settings.
Details specific parameters within the CONFIG menus, starting with Channel Enable.
How to select video sources for each input channel.
How to select audio sources for each input channel.
Configures device behavior when video input is lost during recording.
Selects which channels are displayed on SDI and HDMI monitor outputs.
Selects audio channels for the headphone jack and rear audio outputs.
Sets the 3G SDI output level (A or B) for compatibility.
Controls HDMI output negotiation via EDID or specified type.
Defines the frame recording method based on input format.
Sets the format for progressive media playback.
Selects the reference source for genlock synchronization.
Configures analog audio input and output signal levels.
Sets the IP address type (DHCP or Static) for network connectivity.
Configures network settings for TCP/IP connectivity.
Sets the device name and displays the MAC address.
Manually sets the internal clock, date, and time zone.
Configures the internal clock for Daylight Savings or Standard Time.
Configures the FUNC button for quick menu access.
Adjusts screen dimmer, brightness, and overlay opacity.
Displays device serial number and software version.
Manages saving and recalling system configuration presets.
Resets the Ki Pro GO to its factory default settings.
Overview of parameters for media storage and clip naming.
Sets the name for clips generated by Channel 1, with prohibited characters.
Sets the quality level for clip encoding (Low, Medium, High).
Configures the destination for backup clips.
Sets clip numbering and directory structure for media saving.
Selects the USB media source for clip playback.
Determines if playback stops after one clip or continues through the media.
Enables or disables looped playback for clips.
Introduces remote control of the Ki Pro GO via a web browser.
Overview of the Ki Pro GO's web-based user interface layout and elements.
Describes the Status screen in the Web UI, mirroring front panel status.
How to view alarm messages within the Web UI's Alarms pane.
How to export preset configurations to computer files.
Resets editable parameters to factory defaults via the Web UI.
Displays network configuration (DHCP/Static IP) in the Web UI.
Describes the Firmware screen for checking and updating device firmware.
Step-by-step guide for downloading and installing firmware updates.
Explains the safeboot feature for recovering from failed firmware updates.
Displays available clips for playback and allows media selection.
How to quickly cue clips for review using the playlist.
How to initiate clip playback from the playlist using the Web UI.
Comprehensive technical specifications for the Ki Pro GO.
Details video formats, codec support, and audio capabilities.
Lists supported storage media and file system types.
Details H.264 encoding profiles and target bitrates for various formats.
Explains entropy encoding methods and I-frame/GOP structure.
Details FCC Class A interference statement and caution for the device.
Compliance statement for Canadian digital apparatus (ICES-003).
Lists European Union and EFTA countries where operation is permitted.
Lists conformance standards for safety, emissions, and immunity.
Information on operating environments and ESD compliance recommendations.
Warning about Class A product use and notice on proper equipment recycling.
Compliance notices for Korea, Taiwan, and Japan regarding radio interference.
Provides standard warning, hazard, and caution symbols and their meanings.
Details the hardware warranty period, terms, and exclusions for defects.
Limits AJA Video's liability for damages, data loss, and lost profits.
Specifies governing law (California) and consumer rights under the warranty.
To Next Page
