Need help?Do you have a question about the AKTA design P-900 and is the answer not in the manual?
General| Brand | AKTA design |
|---|---|
| Model | P-900 |
| Category | Water Pump |
| Language | English |
Provides a general overview of the Pump P-900 family and its members.
Details the specific features and capabilities of the P-901 and P-903 models.
Lists accessories that can be connected to the pump system.
Details essential safety guidelines for operating and maintaining the instrument.
Instructions for unpacking the instrument and checking for damage.
Guidelines for installing the instrument in a suitable environment.
Explains how to connect electrical signal cables to the rear panel.
How to connect a chart recorder to the instrument's pressure output.
Details on connecting the pump to a PC via UniNet cables for control.
Instructions for connecting the instrument to the mains power supply.
Step-by-step guide for installing the piston seal rinsing system.
How to connect the inlet tubing to the pump module.
Procedure for removing air from the pump to protect piston seals.
Procedure for running-in a new pump to ensure optimal performance.
How to connect the outlet tubing from the pump head.
Instructions for installing optional accessories like Mixer M-925 and Switch Valves.
How to switch the instrument on and off and the initial self-test sequence.
Explains how to navigate and use the instrument's menu system.
How to navigate back to the main operating menu and adjust values.
Overview of the main operating menu and its various functions.
Detailed instructions on how to start and stop the pump operation.
Essential checks and preparations required before starting a run.
How to set the desired flow rate and start the pump.
How to set the percentage of eluent B for gradient formation.
How to set up and run a simple time or volume-based gradient.
Procedures for ending a run and preparing the pump for storage.
Instructions for safely changing the eluent in the system.
How the instrument behaves and restarts after a power interruption.
Schedule of routine maintenance tasks to be performed regularly.
Best practices for using eluents to ensure optimal pump performance and longevity.
Specific advice for handling aqueous eluents to prevent issues.
Detailed instructions for replacing worn or damaged piston seals.
Procedure for running-in a newly installed piston seal.
Symptoms and procedure for replacing a damaged piston.
Procedures for cleaning or replacing faulty inlet and outlet check valves.
General advice for troubleshooting and contacting support.
Lists common faults and recommended actions to resolve them.
Lists error messages displayed by the instrument and their meanings.
How to check pump pressure using recordings or UNICORN for diagnostics.
Procedure to remove air bubbles causing flow or pressure issues.
Describes the Pump P-900 as a high-performance laboratory pump.
Explains the structure and function of the pump modules and heads.
Describes the principle of operation for the pump's piston actuation.
Describes the manifold block that combines eluent from pump heads.
Explains how system pressure is monitored and displayed.
Details on using an external chart recorder for pressure logging.
Details on using the 'Check' menu for instrument diagnostics.
Overview of the 'Setup' menu for configuring instrument parameters.
Setting up alarms and timers for automated pump control.
Information on service displays accessible only by authorized personnel.
A visual overview of the instrument's menu structure.
Lists the technical specifications and operating data for the pump.
Details on physical dimensions, weight, and materials.
Information on how the instrument is controlled (stand-alone, PC).
Lists materials in contact with eluent and their resistance to solvents.
Specifies power supply, consumption, and digital/analog I/O.
Lists selectable functions and display characteristics.
Physical dimensions, weight, and compliance with EMC and Safety standards.
Lists accessories and spare parts specific to the P-901 model.
Lists accessories and spare parts specific to the P-903 model.
Lists available recorder cables and switch valves.
Lists available mixers and mixer chambers.
Lists various valves, tubing kits, and filter sets.
Lists available tubing connectors, ferrules, and fittings.
Guide to switching on the instrument and starting synchronization.
Steps for setting the flow rate and starting the pump operation.
Instructions for setting the gradient length and target concentration.
Procedure for stopping the pump operation by setting it to END-mode.
To Next Page