Alcatel-Lucent OmniSwitch 10K - Page 83

OmniSwitch OS6860/OS6900/OS10K Troubleshooting Guide Part No.032996-00 Rev.A
AOS Release 7.X and 8.X January 2015
Alcatel-Lucent Page 83 of 148
-> show ip rip
Status = Enabled,
Number of routes = 0,
Number of prefixes = 0,
Host Route Support = Enabled,
Route Tag = 0,
Update interval = 30,
Invalid interval = 180,
Garbage interval = 120,
Holddown interval = 0,
Forced Hold-Down Timer = 0
Now, verify if the peer relationship is established between the two routers using the show ip rip peer
command.
-> show ip rip peer
Total Bad Bad Secs since
IP Address Recvd Packets Routes Version last update
----------------+--------+-------+------+-------+-----------
102.100.0.26 21773 0 0 2 17
102.101.0.26 21768 0 0 2 10
102.102.0.6 21760 0 0 2 27
102.102.0.26 21758 0 0 2 3
The above command output shows the number of updates received as well as the time since the last update. If
the peer relationship is not formed, then the next thing to look for will be the other router to check if it is setup
correctly.
Now, look at the routing table for RIP protocol, using the show ip rip routes command.
-> show ip rip routes
Legends: State: A = Active, H = Holddown, G = Garbage
Destination Gateway State Metric Proto
------------------+-----------------+----+------+------
105.0.0.0/8 +102.100.0.26 A 2 Rip
+102.101.0.26 A 2 Rip
+102.102.0.26 A 2 Rip
105.4.0.0/16 +11.102.15.1 A 1 Redist
105.12.0.0/16 +11.102.15.1 A 1 Redist
105.13.0.0/16 +11.102.15.1 A 1 Redist
105.21.0.0/16 +11.102.15.1 A 1 Redist
105.31.0.0/16 +11.102.15.1 A 1 Redist
192.168.0.0/24 +102.100.0.26 A 3 Rip
+102.101.0.26 A 3 Rip
+102.102.0.26 A 3 Rip
192.168.1.0/24 +102.100.0.26 A 3 Rip
+102.101.0.26 A 3 Rip
+102.102.0.26 A 3 Rip
192.168.2.0/24 +102.100.0.26 A 3 Rip
+102.101.0.26 A 3 Rip
+102.102.0.26 A 3 Rip
Next, clear the switch log using the swlog clear command and then wait for a few seconds and then run the
show log swlog command.
-> show log swlog
Displaying file contents for '/flash/swlog2.log'
FILEID: fileName[/flash/swlog2.log], endPtr[60], configSize[500000], mode[2]
Displaying file contents for '/flash/swlog1.log'
FILEID: fileName[/flash/swlog1.log], endPtr[1433], configSize[500000], mode[1]
Time Stamp Application Level Log Message
------------------------+--------------+-------+--------------------------------
TUE JUN 03 14:23:53 2008 SYSTEM info Switch Logging cleared by command.
File Size=1000000 bytes
TUE JUN 03 14:24:00 2008 DRC info tRip::ripRecv:Received packet from
102.102.0.26