ADB-19 Installation

Outdoor-unit - battery placement:

Indoor-unit:

Important Note:

● If you do not plan to use the device for a long time, such as at a vacation, please remove the

battery from Transmitter, then put them in a safe place.

● Improperly using a battery may cause it to leak and damage nearby items, and can create the

risk of fire and personal injury. Batteries should not be left in an area where the children can

reach them as they may pose a chocking hazard.

● Recycle used batteries following environmental protection practices.

Transmitter Installation:

● Stick the Transmitter on the wall or the door with

double-sided adhesive tape.

Receiver Installation:

● Plug the Receiver into any socket of AC110~240V power.

Battery Installation (Transmitter):

Transmitter uses a 3V CR2032 battery (included).

Open the Transmitter (by pushing in the interface located at the bottom with a flat screw driver)

and place the battery. Please be well noted with the correct battery polarity. To replace a new

battery, operate in the same way.

Press lightly the battery

holder at side

CR2032 3V Lithium Battery

Important Note:

● If you do not plan to use the device for a long time, such as at a vacation, please remove the

battery from Transmitter, then put them in a safe place.

● Improperly using a battery may cause it to leak and damage nearby items, and can create the

risk of fire and personal injury. Batteries should not be left in an area where the children can

reach them as they may pose a chocking hazard.

● Recycle used batteries following environmental protection practices.

Transmitter Installation:

● Stick the Transmitter on the wall or the door with

double-sided adhesive tape.

Receiver Installation:

● Plug the Receiver into any socket of AC110~240V power.

Battery Installation (Transmitter):

Transmitter uses a 3V CR2032 battery (included).

Open the Transmitter (by pushing in the interface located at the bottom with a flat screw driver)

and place the battery. Please be well noted with the correct battery polarity. To replace a new

battery, operate in the same way.

Press lightly the battery

holder at side

CR2032 3V Lithium Battery

ADB-19 Installation

Outdoor-unit:

Indoor-unit:

● Stick the Transmitter on the wall or the door with

double-sided adhesive tape.

Receiver Installation:

● Plug the Receiver into any socket of AC110~240V power.

● Stick the Transmitter on the wall or the door with

double-sided adhesive tape.

Receiver Installation:

● Plug the Receiver into any socket of AC110~240V power.

Connecting:

Accessories List:

● 1 x Receiver ● 1 x Transmitter

● 1 x User Manual ● 1 x Double-sided adhesive

● 1 x 3 volts CR2032 battery for transmitter

Technical Specification:

● Frequency: 433.92MHz+100KHz

● Modulation Type: ASK

● Ring Volume:＞85dB(within 0.5m)

● Channel space: 1 million sets of auto-learning codes

● Receiver bandwidth: ±90KHz

● Reception Sensitivity:＞-105dBm

● Transmitter Power:＜10mW

● Power consumption(Receiver): standby:＜0.3W

● Power consumption(Transmitter): standby:＜5uA working:＜10mA

● Power Supply(Receiver): AC110-240V

● Power Supply(Transmitter): DC 3V (1x CR2032)

● Operating Range:＞150m (in the open air)

Names for Parts:

Instruction Manual

Auto-leaning Code Wireless Door Chime

Model No.: QH-861AK

VOL

MODE

CODE

Important Note:

● If you do not plan to use the device for a long time, such as at a vacation, please remove the

battery from Transmitter, then put them in a safe place.

● Improperly using a battery may cause it to leak and damage nearby items, and can create the

risk of fire and personal injury. Batteries should not be left in an area where the children can

reach them as they may pose a chocking hazard.

● Recycle used batteries following environmental protection practices.

Transmitter Installation:

● Stick the Transmitter on the wall or the door with

double-sided adhesive tape.

Receiver Installation:

● Plug the Receiver into any socket of AC110~240V power.

Battery Installation (Transmitter):

Transmitter uses a 3V CR2032 battery (included).

Open the Transmitter (by pushing in the interface located at the bottom with a flat screw driver)

and place the battery. Please be well noted with the correct battery polarity. To replace a new

battery, operate in the same way.

Press lightly the battery

holder at side

CR2032 3V Lithium Battery

1x1x

<10 sec.

Accessories List:

● 1 x Receiver ● 1 x Transmitter

● 1 x User Manual ● 1 x Double-sided adhesive

● 1 x 3 volts CR2032 battery for transmitter

Technical Specification:

● Frequency: 433.92MHz+100KHz

● Modulation Type: ASK

● Ring Volume:＞85dB(within 0.5m)

● Channel space: 1 million sets of auto-learning codes

● Receiver bandwidth: ±90KHz

● Reception Sensitivity:＞-105dBm

● Transmitter Power:＜10mW

● Power consumption(Receiver): standby:＜0.3W

● Power consumption(Transmitter): standby:＜5uA working:＜10mA

● Power Supply(Receiver): AC110-240V

● Power Supply(Transmitter): DC 3V (1x CR2032)

● Operating Range:＞150m (in the open air)

Names for Parts:

Instruction Manual

Auto-leaning Code Wireless Door Chime

Model No.: QH-861AK

VOL

MODE

CODE

Accessories List:

● 1 x Receiver

● 1 x User Manual

● 1 x 3 volts CR2032 battery for transmitter

Technical Specification:

● Frequency: 433.92MHz+100KHz

● Modulation Type: ASK

● Ring Volume:＞85dB(within 0.5m)

● Channel space: 1 million sets of auto-learning co

● Receiver bandwidth: ±90KHz

● Reception Sensitivity:＞-105dBm

● Transmitter Power:＜10mW

● Power consumption(Receiver): standby:＜0.3W

● Power consumption(Transmitter): standby:＜5uA

● Power Supply(Receiver): AC110-240V

● Power Supply(Transmitter): DC 3V (1x CR2032)

● Operating Range:＞150m (in the open air)

Names for Parts:

Instruction

Auto-leaning Code W

Model No.: QH-861AK

VOL

MODE

CODE

5 sec.

Unregister

Important Note:

● If you do not plan to use the device for a long time, such as at a vacation, please remove the

battery from Transmitter, then put them in a safe place.

● Improperly using a battery may cause it to leak and damage nearby items, and can crea

risk of fire and personal injury. Batteries should not be left in an area where the children

reach them as they may pose a chocking hazard.

● Recycle used batteries following environmental protection practices.

Transmitter Installation:

● Stick the Transmitter on the wall or the door with

double-sided adhesive tape.

Battery Installation (Transmitter):

Transmitter uses a 3V CR2032 battery (included).

Open the Transmitter (by pushing in the interface located at the bottom with a flat screw d

and place the battery. Please be well noted with the correct battery polarity. To replace a new

battery, operate in the same way.

Press lightly the battery

holder at side

CR2032 3V Lithium Battery

ADB-19 Installation

Outdoor-unit:

Indoor-unit:

● Stick the Transmitter on the wall or the door with

double-sided adhesive tape.

Receiver Installation:

● Plug the Receiver into any socket of AC110~240V power.

● Stick the Transmitter on the wall or the door with

double-sided adhesive tape.

Receiver Installation:

● Plug the Receiver into any socket of AC110~240V power.

Connecting:

Accessories List:

● 1 x Receiver ● 1 x Transmitter

● 1 x User Manual ● 1 x Double-sided adhesive

● 1 x 3 volts CR2032 battery for transmitter

Technical Specification:

● Frequency: 433.92MHz+100KHz

● Modulation Type: ASK

● Ring Volume:＞85dB(within 0.5m)

● Channel space: 1 million sets of auto-learning codes

● Receiver bandwidth: ±90KHz

● Reception Sensitivity:＞-105dBm

● Transmitter Power:＜10mW

● Power consumption(Receiver): standby:＜0.3W

● Power consumption(Transmitter): standby:＜5uA working:＜10mA

● Power Supply(Receiver): AC110-240V

● Power Supply(Transmitter): DC 3V (1x CR2032)

● Operating Range:＞150m (in the open air)

Names for Parts:

Instruction Manual

Auto-leaning Code Wireless Door Chime

Model No.: QH-861AK

VOL

MODE

CODE

Important Note:

● If you do not plan to use the device for a long time, such as at a vacation, please remove the

battery from Transmitter, then put them in a safe place.

● Improperly using a battery may cause it to leak and damage nearby items, and can create the

risk of fire and personal injury. Batteries should not be left in an area where the children can

reach them as they may pose a chocking hazard.

● Recycle used batteries following environmental protection practices.

Transmitter Installation:

● Stick the Transmitter on the wall or the door with

double-sided adhesive tape.

Receiver Installation:

● Plug the Receiver into any socket of AC110~240V power.

Battery Installation (Transmitter):

Transmitter uses a 3V CR2032 battery (included).

Open the Transmitter (by pushing in the interface located at the bottom with a flat screw driver)

and place the battery. Please be well noted with the correct battery polarity. To replace a new

battery, operate in the same way.

Press lightly the battery

holder at side

CR2032 3V Lithium Battery

1x1x

<10 sec.

Accessories List:

● 1 x Receiver ● 1 x Transmitter

● 1 x User Manual ● 1 x Double-sided adhesive

● 1 x 3 volts CR2032 battery for transmitter

Technical Specification:

● Frequency: 433.92MHz+100KHz

● Modulation Type: ASK

● Ring Volume:＞85dB(within 0.5m)

● Channel space: 1 million sets of auto-learning codes

● Receiver bandwidth: ±90KHz

● Reception Sensitivity:＞-105dBm

● Transmitter Power:＜10mW

● Power consumption(Receiver): standby:＜0.3W

● Power consumption(Transmitter): standby:＜5uA working:＜10mA

● Power Supply(Receiver): AC110-240V

● Power Supply(Transmitter): DC 3V (1x CR2032)

● Operating Range:＞150m (in the open air)

Names for Parts:

Instruction Manual

Auto-leaning Code Wireless Door Chime

Model No.: QH-861AK

VOL

MODE

CODE

Accessories List:

● 1 x Receiver

● 1 x User Manual

● 1 x 3 volts CR2032 battery for transmitter

Technical Specification:

● Frequency: 433.92MHz+100KHz

● Modulation Type: ASK

● Ring Volume:＞85dB(within 0.5m)

● Channel space: 1 million sets of auto-learning co

● Receiver bandwidth: ±90KHz

● Reception Sensitivity:＞-105dBm

● Transmitter Power:＜10mW

● Power consumption(Receiver): standby:＜0.3W

● Power consumption(Transmitter): standby:＜5uA

● Power Supply(Receiver): AC110-240V

● Power Supply(Transmitter): DC 3V (1x CR2032)

● Operating Range:＞150m (in the open air)

Names for Parts:

Instruction

Auto-leaning Code W

Model No.: QH-861AK

VOL

MODE

CODE

5 sec.

Unregister

Important Note:

● If you do not plan to use the device for a long time, such as at a vacation, please remove the

battery from Transmitter, then put them in a safe place.

● Improperly using a battery may cause it to leak and damage nearby items, and can crea

risk of fire and personal injury. Batteries should not be left in an area where the children

reach them as they may pose a chocking hazard.

● Recycle used batteries following environmental protection practices.

Transmitter Installation:

● Stick the Transmitter on the wall or the door with

double-sided adhesive tape.

Battery Installation (Transmitter):

Transmitter uses a 3V CR2032 battery (included).

Open the Transmitter (by pushing in the interface located at the bottom with a flat screw d

and place the battery. Please be well noted with the correct battery polarity. To replace a new

battery, operate in the same way.

Press lightly the battery

holder at side

CR2032 3V Lithium Battery

CR2032 3V

Lithium Battery

Nameplate

thin-tipped

cover

(not included)

tweezers

(not included)

screwdriver

Important Note:

● If you do not plan to use the device for a long time, such as at a vacation, please remove the

battery from Transmitter, then put them in a safe place.

● Improperly using a battery may cause it to leak and damage nearby items, and can create the

risk of fire and personal injury. Batteries should not be left in an area where the children can

reach them as they may pose a chocking hazard.

● Recycle used batteries following environmental protection practices.

Transmitter Installation:

● Stick the Transmitter on the wall or the door with

double-sided adhesive tape.

Receiver Installation:

● Plug the Receiver into any socket of AC110~240V power.

Battery Installation (Transmitter):

Transmitter uses a 3V CR2032 battery (included).

Open the Transmitter (by pushing in the interface located at the bottom with a flat screw driver)

and place the battery. Please be well noted with the correct battery polarity. To replace a new

battery, operate in the same way.

Press lightly the battery

holder at side

CR2032 3V Lithium Battery

Important Note:

● If you do not plan to use the device for a long time, such as at a vacation, please remove the

battery from Transmitter, then put them in a safe place.

● Improperly using a battery may cause it to leak and damage nearby items, and can create the

risk of fire and personal injury. Batteries should not be left in an area where the children can

reach them as they may pose a chocking hazard.

● Recycle used batteries following environmental protection practices.

Transmitter Installation:

● Stick the Transmitter on the wall or the door with

double-sided adhesive tape.

Receiver Installation:

● Plug the Receiver into any socket of AC110~240V power.

Battery Installation (Transmitter):

Transmitter uses a 3V CR2032 battery (included).

Open the Transmitter (by pushing in the interface located at the bottom with a flat screw driver)

and place the battery. Please be well noted with the correct battery polarity. To replace a new

battery, operate in the same way.

Press lightly the battery

holder at side

CR2032 3V Lithium Battery

Important Note:

● If you do not plan to use the device for a long time, such as at a vacation, please remove the

battery from Transmitter, then put them in a safe place.

● Improperly using a battery may cause it to leak and damage nearby items, and can create the

risk of fire and personal injury. Batteries should not be left in an area where the children can

reach them as they may pose a chocking hazard.

● Recycle used batteries following environmental protection practices.

Transmitter Installation:

● Stick the Transmitter on the wall or the door with

double-sided adhesive tape.

Receiver Installation:

● Plug the Receiver into any socket of AC110~240V power.

Battery Installation (Transmitter):

Transmitter uses a 3V CR2032 battery (included).

Open the Transmitter (by pushing in the interface located at the bottom with a flat screw driver)

and place the battery. Please be well noted with the correct battery polarity. To replace a new

battery, operate in the same way.

Press lightly the battery

holder at side

CR2032 3V Lithium Battery

Important Note:

● If you do not plan to use the device for a long time, such as at a vacation, please remove the

battery from Transmitter, then put them in a safe place.

● Improperly using a battery may cause it to leak and damage nearby items, and can create the

risk of fire and personal injury. Batteries should not be left in an area where the children can

reach them as they may pose a chocking hazard.

● Recycle used batteries following environmental protection practices.

Transmitter Installation:

● Stick the Transmitter on the wall or the door with

double-sided adhesive tape.

Receiver Installation:

● Plug the Receiver into any socket of AC110~240V power.

Battery Installation (Transmitter):

Transmitter uses a 3V CR2032 battery (included).

Open the Transmitter (by pushing in the interface located at the bottom with a flat screw driver)

and place the battery. Please be well noted with the correct battery polarity. To replace a new

battery, operate in the same way.

Press lightly the battery

holder at side

CR2032 3V Lithium Battery

CR2032 3V

Lithium Battery

Nameplate

thin-tipped

cover

(not included)

tweezers

(not included)

screwdriver

Alecto ADB-19 - Installation Manual

Other manuals for Alecto ADB-19

Related product manuals