<JAPANESE CAR>
SCrews (M5 x 8)
(Included)
• Secure the ground lead
of
the unit to a clean metal spot using a screw
(oJ)
already attached 10 the vehicle's chassis.
USB cable connection
Insett a USB cable into the unit, and fix with a lock screw.
iPod Connection (sold separately)
USB connection
Connect
USB
cable to
an
iPod with iPod Dock interface cable.
iPod Dock Interface Cable
Full
Speed™
connection
Connect Full
Speed™
connector
to
an iPod with FULL
SPEED
TM
connection cable (KCE-422i).
!til
~
'4
FULL
SPEEDTM
.-
'":.
Connection Cable
(KCE-4221) (Sold separately)
Remove the iPod
Remove the iPod from FULL
SPEEDTM
Connection Cable or iPod
Dock interface cable.
•
If
USB is connected, after the unit has been changed 10 a source
other than the iPod, remove the
iPod.
If
the iPod is removed
in
the
iPod mode. data may cause damage.
•
If
sound is not output
or
the iPod is not recognized even when the
iPod is connected. remove the iPod once, then connect it again.
or
reset the iPod.
• Before connecting the iPod to this unit. set the EQfunction
ofiPod
to
OFF.
USB memory Connection (sold separately)
Connect USB memory
Connect
USB
memory
to
USB
cable.
USB cable
C
IlJ"~
III
I
USB memory
Remove USB memory
Pullout
USB
memory squarely from the
USB
cable.
USB cable
"(':;;;;'F==~
III
I
USB memory
• When removing USB memory, pull it out straight.
•
If
sound is not output
or
USB memory is not recognized even when
USB memory is connected. remove USB memory once, then connect
it again.
• Change 10 a source other than the USB memory mode. then remove
the USB memory.
If
the USB memory is removed
in
the USB memory
mode. data may be damaged.
Portable Audio Player Connection (sold separately)
Connect Portable audio player
Connect
the
cable
supplied
with a Portable
audio
player to
the USB cable.
USB cable
_-""-'>--_!!U~
I
II
Supplied cable for the Portable audio player
Remove Portable audio player
Disconnect
the Portable
audio
player from the
supplied
player cable.
• Refer also to the Owner's Manual
of
the Portable audio player.
43-EN
<JAPANESE CAR>
SCrews (M5 x 8)
(Included)
• Secure the ground lead
of
the unit to a clean metal spot using a screw
(oJ)
already attached 10 the vehicle's chassis.
USB cable connection
Insett a USB cable into the unit, and fix with a lock screw.
iPod Connection (sold separately)
USB connection
Connect
USB
cable to
an
iPod with iPod Dock interface cable.
iPod Dock Interface Cable
Full
Speed™
connection
Connect Full
Speed™
connector
to
an iPod with FULL
SPEED
TM
connection cable (KCE-422i).
!til
~
'4
FULL
SPEEDTM
.-
'":.
Connection Cable
(KCE-4221) (Sold separately)
Remove the iPod
Remove the iPod from FULL
SPEEDTM
Connection Cable or iPod
Dock interface cable.
•
If
USB is connected, after the unit has been changed 10 a source
other than the iPod, remove the
iPod.
If
the iPod is removed
in
the
iPod mode. data may cause damage.
•
If
sound is not output
or
the iPod is not recognized even when the
iPod is connected. remove the iPod once, then connect it again.
or
reset the iPod.
• Before connecting the iPod to this unit. set the EQfunction
ofiPod
to
OFF.
USB memory Connection (sold separately)
Connect USB memory
Connect
USB
memory
to
USB
cable.
USB cable
C
IlJ"~
III
I
USB memory
Remove USB memory
Pullout
USB
memory squarely from the
USB
cable.
USB cable
"(':;;;;'F==~
III
I
USB memory
• When removing USB memory, pull it out straight.
•
If
sound is not output
or
USB memory is not recognized even when
USB memory is connected. remove USB memory once, then connect
it again.
• Change 10 a source other than the USB memory mode. then remove
the USB memory.
If
the USB memory is removed
in
the USB memory
mode. data may be damaged.
Portable Audio Player Connection (sold separately)
Connect Portable audio player
Connect
the
cable
supplied
with a Portable
audio
player to
the USB cable.
USB cable
_-""-'>--_!!U~
I
II
Supplied cable for the Portable audio player
Remove Portable audio player
Disconnect
the Portable
audio
player from the
supplied
player cable.
• Refer also to the Owner's Manual
of
the Portable audio player.
43-EN