21-EN
5 To store the adjusted setting value, touch and hold
[Preset 1], [Preset 2], or [Preset 3] for at least 2 seconds.
• Settings exceeding the frequency of adjacent bands are not available.
• While adjusting the Graphic EQ, you should consider the frequency
response of the connected speakers.
• When the Graphic EQ is adjusted, the Equalizer Presets are overridden.
• When Equalizer Presets is set, the linked Graphic EQ settings are also
changed. We recommend storing Graphic EQ settings in a Preset in
advance.
•Touch [Flat] to initialize all values.
Calling the Graphic EQ adjusted value
To uc h [Preset 1], [Preset 2], or [Preset 3].
The setting stored in the Preset will be recalled.
Time Correction Settings
[Time Correction] is selected on the Sound Setup Menu screen.
Before performing the following procedures, see “About Time
Correction” (page 23).
Setting item:
Time Correction
1 To uc h [Time Correction] on the Sound Setup menu
screen.
2 Touch the Correction mode button, and then select [ms],
[cm] or [inch].
3 To uc h [] or [] for each speaker to adjust the time or
distance.
0.0 msec to 9.9 msec (0.1 msec/step)
0.0 cm (0.0 inch) to 336.6 cm (132.56 inch) (3.4 cm/step)
All speaker setting values are adjustable in the range of 20 ms or
680 cm.
4 To store the adjusted setting value, touch and hold
[Preset 1], [Preset 2], or [Preset 3] for at least 2 seconds.
•Touch [Flat] to set all values to 0.0.
• If the Rear Speaker setting is Off, the Rear Speaker setting cannot be
edited (page 22).
• If the Subwoofer setting is Off, the Subwoofer setting cannot be edited
(page 22).
Calling the Time Correction Value
Calling the pre-set time correction value.
To uc h [Preset 1], [Preset 2], or [Preset 3] on the time
correction screen.
The setting stored in the Preset will be recalled.
Crossover Settings (X-Over)
[X-Over] is selected on the Sound Setup Menu screen.
Before performing the following procedures, see “About the Crossover”
(page 23).
Setting item:
X-Over
1 To uc h [X-Over] on the Sound Setup menu screen.
2 To uc h [Channel], and then select [Front HPF], [Rear
HPF] or [SubW.LPF].
3 Adjust the crossover to your preference.
Selecting the Cut-Off Frequency
Touch [] or [] of “Freq.” (Frequency), and then select the cut-
off frequency.
Setting contents:
20.0 / 25.0 / 31.5 / 40.0 / 50.0 / 63.0 / 80.0 (Initial setting) / 100.0 / 125.0 /
160.0 / 200.0 Hz
Adjusting the Slope
Touch [] or [] of “Slope”, and then adjust the HPF or LPF slope.
Setting contents:
0 (Initial setting) / 6 / 12 / 18 / 24 dB/oct.
Adjusting the Level
Touch [] or [] of “Level”, and then adjust the HPF or LPF level.
Setting contents:
-12 to 0 dB (Initial setting: 0)
4 Repeat steps 2 to 3 to make adjustment to the other
channels.
5 To store the adjusted setting value, touch and hold
[Preset 1], [Preset 2], or [Preset 3] for at least 2 seconds.
•Touch [Flat] to initialize all values.
• If the Rear Speaker setting is Off, the Rear Speaker setting cannot be
edited (page 22).
• If the Subwoofer setting is Off, the Subwoofer setting cannot be edited
(page 22).
• While adjusting the X-Over you should consider the frequency response
of the connected speakers.
Calling the X-Over adjusted value
To uc h [Preset 1], [Preset 2], or [Preset 3].
The setting stored in the Preset will be recalled.
To Next Page
Loading...
