51-EN
3
Touch [ ] or [ ] of the desired MX mode.
• Music source (such as CDs, iPod, etc.) level can be set.
MX CD (OFF, CD MX 1 to 3)
CD mode processes a large quantity of data. This data is used
to
reproduce the sound cleanly by making use of the data
quantity.
MX CMPM (OFF, CMPM MX 1 to 3)
This corrects information that was omitted at the time of
c
ompression. This reproduces a well-balanced sound close to
the original.
MX DVD (OFF, Movie MX 1 to 2)
The dialogue portion of the video is reproduced more clearly.
MX AUX (OFF, CMPM MX, Movie MX, Music MX)
Choose the MX mode (CMPM, Music, or Movie) that
c
orresponds to the media connected.
• When OFF is selected, MX effect of each MX mode will be OFF.
• Eac
h music source, such as CD, and MP3 can have its own MX
setting.
• M
X mode does not function when MX is ON for FM, MW, LW radio.
• M
X CMPM is applied for MP3/WMA/AAC and iPod/iPhone.
• T
he MX setting can be performed only when a source is currently
selected.
• T
his function is inoperable when Defeat is set to ON.
Before performing the following procedures, refer to “About the
Crossover” (page 55).
Setting item : X-Over
1
Touch [ ] or [ ] of X-Over to select L/R or L+R.
2
Touch [ ] of X-Over.
A speaker list on the X-OVER screen is displayed.
3
Touch [ ] of the band to be adjusted.
The screen changes to the X-Over screen to be adjusted.
4.2ch (FRONT/REAR/SUBW.) System / (L+R)
Setting contents:
Low (SUB-W) / Mid (REAR) / High (FRONT)
4.2ch (FRONT/REAR/SUBW.) System / (L/R)
Setting contents:
Low (SUB-W)-L / Low (SUB-W)-R / Mid (REAR)-L /
Mid (REAR)-R / High (FRONT)-L / High (FRONT)-R
4
Adjust the crossover to your preference.
Selecting the Cut-Off Frequency
Touch [ ] or [ ] of Freq., then select the cut-off frequency
(crossover point).
The adjustable bandwidth differs depending on the speaker
(channel).
4.2ch (FRONT/REAR/SUBW.) System
Setting contents:
Low (SUB-W) 20 Hz~200 Hz
Mid (REAR) 20 Hz~200 Hz
High (FRONT) 20 Hz~200 Hz
Adjusting the Slope
Touch [ ] or [ ] of Slope, then adjust the HPF or LPF slope.
Adjustable slope: FLAT, –6 dB/oct., –12 dB/oct., –18 dB/oct.,
–24 dB/oct.
Adjusting the Level
Touch [ ] or [ ] of Level, then adjust the HPF or LPF level.
Adjustable output level: -12 to 0 dB.
5
Repeat steps 3 to 4 to make adjustment to the other
bands.
2.2ch (3WAY) System / (L+R)
Setting contents:
Low / Mid-L / Mid-H / High
2.2ch (3WAY) System / (L/R)
Setting contents:
Low-L / Low-R / Mid-L-L / Mid-L-R / Mid-H-L /
Mid-H-R / High-L / High-R
4
Adjust the crossover to your preference.
Selecting the Cut-Off Frequency
Touch [ ] or [ ] of Freq., then select the cut-off frequency
(crossover point).
The adjustable bandwidth differs depending on the speaker
(channel).
2.2ch (3WAY) System
Setting contents:
Low / Mid-L 20 Hz~200 Hz
Mid-H 20 Hz~20 kHz
High (1 kHz~20 kHz)
*
1
/(20 Hz~20 kHz)*
2
*
1
When Factory’s is selected, refer to “Setting the Response Slope for
the High Range Speaker (TW Setup)” (page 53).
*
2
When User’s is selected, refer to “Setting the Response Slope for the
High Range Speaker (TW Setup)” (page 53).
(DVD Music)
This disc contains a large quantity of data such as music clip.
MX uses this data to reproduce the sound accurately.
Adjusting the Crossover Settings (X-Over)
L/R: Different adjustment values can be set for the left and
right channels.
L+R: Sets the same adjustment values for the left and right
ch
annels.
4.2ch (FRONT/REAR/SUBW.) System
2.2ch (3WAY) System
To Next Page
Loading...
