Inserting/Ejecting
a
Disc
1 Press
OPEN
on the unit.
The display changes to the EJECTfTlLT screen.
2 Insert a disc:
Touch [OPEN] on the EJECTfTlLT screen.
The movable monitor will open, then insert a disc into the
disc slot. Inserting a disc will close the monitor
automatically.
Eject the disc:
Touch [EJECT] of DISC on the EJECTfTlLT screen.
The movable monitor will open. Then the disc
is
ejected.
3 Touch
[CLOSE]
on the EJECTmLT screen.
The movable monitor will close.
o Touching
[~J
returns to the earlier main source screen.
o Do not apply shock to the movable monitor when it is open as it may
result
in
malfunction
of
the unit.
o The monitor may be dim during low temperature
and
immediately
after turning on the power. The brightness will return to normal as
time elapses.
o The monitor will stop at the set tilt angle when closing.
CAUTION
Keep hands (or any other object) away from the monitor while it
is opening
or
closing to avoid damage
or
injury. The back
of
the
movable monitor will get very warm under
nonnal
operating
conditions. This is not a malfunction. Do not touch.
Adjusting
the
Monitor
Viewing
Angle
Adjust the monitor's angle for better visibility.
1 Press
OPEN
on the unit.
The display changes to the EJECTfTlLT screen.
2 Touch
[oA]
or
[~]
of
TILT
to
adjust the desired
monitor angle.
The monitor angle can be adjusted
in
5 stages.
3 Touch
[~]
to
return
to
the previous screen.
o
If
the monitor touches an obstacle while the angle is being adjusted,
it will stop immediately.
o The screen color will vary when viewed at certain angles. Adjust the
screen angle
for
the best viewing position.
o
If
the voltage
of
the vehicle's battery power is low. the screen may
blink when the screen angle is changed. This is
nonnal
and not a
malfunction.
o Touching
and
holding
[~J
for
at least 2 seconds will change to the
main source screen.
12-EN
Adjusting
the
Volume
Adjust the volume
by
pressing V
or
/'\.
Volume decreases/increases continuously by pressing and
holding
V or
/'\.
Volume: 0 - 35
Lowering
Volume
Quickly
Activating the Audio Mute function will instantly lower the volume
level
by
20 dB.
Press
MUTE
to
activate the
MUTE
mode.
The audio level will decrease by about 20 dB.
Pressing
MUTE
again will bring the audio back
to
its
previous level.
How
to
view
the
Display
o
Be
sure to touch the button lightly with the
pad
of
yourfinger on the
display to protect the display.
o
If
you touch a button and there is no reaction, remove yourfinger
from the display.
and
try again.
About
the
button
descriptions
used In
this
Owner's Manual
o Soft buttons, onesfound in the display, are shown in bold
enclosed in brackets, [
J(e.g. [SOURCE]).
o Whenever a soft button
and
a head unit button have the same
function, the explanations in this Owner's Manual will describe
the function
of
the soft button.
Here is an example explanation for the Radio mode display on how to
recall a source.
1 Touch
[SOURCE]
on
the main screen.
The SOURCE selection screen is displayed.
Display example
for
SOURCE
selection
screen
0
a 9
SOURCE
VISUAL
SETUP
SOURCE
SEL.
ESC
ill'
RADIO
D!SC
USB
AUOIO
-""-"
,-
rJ
~
12:34
:1ll'JlniI'Jcf1
='
RSE
CD
Changes
to VISUAL selection screen.
Set to VISUAL
in
"Setting the VISUAL Soft Button"
(on page 39).
®
Changes
to
SETUP selection screen.
@
Changes
to
main
source screen.
@
Displays
source
modes
that
can
be
selected
(The kind of source modes that are displayed varies
depending on connection and setting).
Inserting/Ejecting
a
Disc
1 Press
OPEN
on the unit.
The display changes to the EJECTfTlLT screen.
2 Insert a disc:
Touch [OPEN] on the EJECTfTlLT screen.
The movable monitor will open, then insert a disc into the
disc slot. Inserting a disc will close the monitor
automatically.
Eject the disc:
Touch [EJECT] of DISC on the EJECTfTlLT screen.
The movable monitor will open. Then the disc
is
ejected.
3 Touch
[CLOSE]
on the EJECTmLT screen.
The movable monitor will close.
o Touching
[~J
returns to the earlier main source screen.
o Do not apply shock to the movable monitor when it is open as it may
result
in
malfunction
of
the unit.
o The monitor may be dim during low temperature
and
immediately
after turning on the power. The brightness will return to normal as
time elapses.
o The monitor will stop at the set tilt angle when closing.
CAUTION
Keep hands (or any other object) away from the monitor while it
is opening
or
closing to avoid damage
or
injury. The back
of
the
movable monitor will get very warm under
nonnal
operating
conditions. This is not a malfunction. Do not touch.
Adjusting
the
Monitor
Viewing
Angle
Adjust the monitor's angle for better visibility.
1 Press
OPEN
on the unit.
The display changes to the EJECTfTlLT screen.
2 Touch
[oA]
or
[~]
of
TILT
to
adjust the desired
monitor angle.
The monitor angle can be adjusted
in
5 stages.
3 Touch
[~]
to
return
to
the previous screen.
o
If
the monitor touches an obstacle while the angle is being adjusted,
it will stop immediately.
o The screen color will vary when viewed at certain angles. Adjust the
screen angle
for
the best viewing position.
o
If
the voltage
of
the vehicle's battery power is low. the screen may
blink when the screen angle is changed. This is
nonnal
and not a
malfunction.
o Touching
and
holding
[~J
for
at least 2 seconds will change to the
main source screen.
12-EN
Adjusting
the
Volume
Adjust the volume
by
pressing V
or
/'\.
Volume decreases/increases continuously by pressing and
holding
V or
/'\.
Volume: 0 - 35
Lowering
Volume
Quickly
Activating the Audio Mute function will instantly lower the volume
level
by
20 dB.
Press
MUTE
to
activate the
MUTE
mode.
The audio level will decrease by about 20 dB.
Pressing
MUTE
again will bring the audio back
to
its
previous level.
How
to
view
the
Display
o
Be
sure to touch the button lightly with the
pad
of
yourfinger on the
display to protect the display.
o
If
you touch a button and there is no reaction, remove yourfinger
from the display.
and
try again.
About
the
button
descriptions
used In
this
Owner's Manual
o Soft buttons, onesfound in the display, are shown in bold
enclosed in brackets, [
J(e.g. [SOURCE]).
o Whenever a soft button
and
a head unit button have the same
function, the explanations in this Owner's Manual will describe
the function
of
the soft button.
Here is an example explanation for the Radio mode display on how to
recall a source.
1 Touch
[SOURCE]
on
the main screen.
The SOURCE selection screen is displayed.
Display example
for
SOURCE
selection
screen
0
a 9
SOURCE
VISUAL
SETUP
SOURCE
SEL.
ESC
ill'
RADIO
D!SC
USB
AUOIO
-""-"
,-
rJ
~
12:34
:1ll'JlniI'Jcf1
='
RSE
CD
Changes
to VISUAL selection screen.
Set to VISUAL
in
"Setting the VISUAL Soft Button"
(on page 39).
®
Changes
to
SETUP selection screen.
@
Changes
to
main
source screen.
@
Displays
source
modes
that
can
be
selected
(The kind of source modes that are displayed varies
depending on connection and setting).
To Next Page
Loading...
