Menu Operations
@op
~
Touch [KEY].
The menu operation
mode
will
be
displayed.
Touch [KEY].
The menu operation mode appears.
2 Touch [KEY] again.
The numeric keypad input
mode
screen appears.
Touch
[RETURN)
to
return
to
the
previous
display.
2 Select a desired menu item
by
touching
[AI.
[~).
[
....
1or
[~I·
3 Touch [ENTERI to confirm the selected item.
Numeric Keypad Input Operations
@op
~
• Play Position Memory Function
Even
if
you turn power
off
or
switch the Ignition key
to
OFF
during playback
or
change the source,
playback will continue from the point where
playback stopped when the power
is
turned
ON
again.
o The reverse side
of
a double-sided DVD will not be played
automatically.
Remove the disc, turn it over, and reinsert
it.
o DO NOT insert discs containing maps
for
the navigation system.
Doing so could result in damage.
o Refer also to "DVD Setup" (pages 29 to 34).
o Be sure the remote input lead is connected to the remote output lead
of
this unit when a DVD changer
or
DVD player is connected.
If
not
correctly connected, touch operation cannot
be
performed.
o
To
return to the previous screen during Video CD playback (when
PBC is set to ON). touch
[:!::J]
after touching [PUZ]
of
thefunction
guide. However, the function may vary depending on the disc.
o
"CANT
DOWNMIX" is displayed when a Downmix (multi-channel
signals are mixed into 2ch) prohibitedsection
of
a DVD-Audio disc is
played.
In
this case, only the LchiRch recorded on the disc is output
as sound. (The sound
of
Center speaker, L-surround speaker, R-
surround speaker,
and
Subwoofer is not output.)
o While "INDEX READING" is displayed by DivX®. thefast-
forwardingljast-reversing
and
repeatfunctions, etc. cannot be used.
o The operation screen changes to the visual screen in the DVD
or
Video CD mode
for
5seconds after an operation has been performed.
Touch the display panel to display the operation screen again.
o The display mode can be changed by touching [WIDE].
For operation, see "Switching Display Modes" on page 28.
InsertingJEjecting a Disc
Refer to "Inserting/Ejecting a Disc" (page 12).
1 Touch [SOURCE) on the main source screen.
The SOURCE selection screen is displayed.
2 Touch [DISC).
The display shows the DISC mode screen.
Insert a disc with the label side facing up. The unit starts to
play the disc.
When an optional Alpine DVD player
is
connected:
Insert a disc into the DVDNideo CD/CD player. the player
starts playing.
On DVDs and Video CDs with playback control (PBC), menu screens
may appear automatically.
If
this happens, perform the operation
described below to start playback.
o
To
play back a DVD-Audio disc, set
"VCAP"
in "Setting
of
the DVD-
Audio Playback
Mode"
(page
33).
Direct Menu Operations @§![)
~
1 Touch the
DVD
menu directly.
o Some operations cannot be performeddepending on the disc.
The
numeric
keypad input
screen closes
when
the
area
is
touched
while displayed.
Touch
[:!::J)
to
close
the
numeric
keypad input screen.
3 Touch a desired number.
4 Touch [ENT] on the numeric keypad mode screen to
confirm your selection.
20-EN
Menu Operations
@op
~
Touch [KEY].
The menu operation
mode
will
be
displayed.
Touch [KEY].
The menu operation mode appears.
2 Touch [KEY] again.
The numeric keypad input
mode
screen appears.
Touch
[RETURN)
to
return
to
the
previous
display.
2 Select a desired menu item
by
touching
[AI.
[~).
[
....
1or
[~I·
3 Touch [ENTERI to confirm the selected item.
Numeric Keypad Input Operations
@op
~
• Play Position Memory Function
Even
if
you turn power
off
or
switch the Ignition key
to
OFF
during playback
or
change the source,
playback will continue from the point where
playback stopped when the power
is
turned
ON
again.
o The reverse side
of
a double-sided DVD will not be played
automatically.
Remove the disc, turn it over, and reinsert
it.
o DO NOT insert discs containing maps
for
the navigation system.
Doing so could result in damage.
o Refer also to "DVD Setup" (pages 29 to 34).
o Be sure the remote input lead is connected to the remote output lead
of
this unit when a DVD changer
or
DVD player is connected.
If
not
correctly connected, touch operation cannot
be
performed.
o
To
return to the previous screen during Video CD playback (when
PBC is set to ON). touch
[:!::J]
after touching [PUZ]
of
thefunction
guide. However, the function may vary depending on the disc.
o
"CANT
DOWNMIX" is displayed when a Downmix (multi-channel
signals are mixed into 2ch) prohibitedsection
of
a DVD-Audio disc is
played.
In
this case, only the LchiRch recorded on the disc is output
as sound. (The sound
of
Center speaker, L-surround speaker, R-
surround speaker,
and
Subwoofer is not output.)
o While "INDEX READING" is displayed by DivX®. thefast-
forwardingljast-reversing
and
repeatfunctions, etc. cannot be used.
o The operation screen changes to the visual screen in the DVD
or
Video CD mode
for
5seconds after an operation has been performed.
Touch the display panel to display the operation screen again.
o The display mode can be changed by touching [WIDE].
For operation, see "Switching Display Modes" on page 28.
InsertingJEjecting a Disc
Refer to "Inserting/Ejecting a Disc" (page 12).
1 Touch [SOURCE) on the main source screen.
The SOURCE selection screen is displayed.
2 Touch [DISC).
The display shows the DISC mode screen.
Insert a disc with the label side facing up. The unit starts to
play the disc.
When an optional Alpine DVD player
is
connected:
Insert a disc into the DVDNideo CD/CD player. the player
starts playing.
On DVDs and Video CDs with playback control (PBC), menu screens
may appear automatically.
If
this happens, perform the operation
described below to start playback.
o
To
play back a DVD-Audio disc, set
"VCAP"
in "Setting
of
the DVD-
Audio Playback
Mode"
(page
33).
Direct Menu Operations @§![)
~
1 Touch the
DVD
menu directly.
o Some operations cannot be performeddepending on the disc.
The
numeric
keypad input
screen closes
when
the
area
is
touched
while displayed.
Touch
[:!::J)
to
close
the
numeric
keypad input screen.
3 Touch a desired number.
4 Touch [ENT] on the numeric keypad mode screen to
confirm your selection.
20-EN
To Next Page
Loading...
