Installation
•
If
B
or
C is used. make sure that there is a enough space depthwise
before installing the unit.
If
the unit isforcibly pushed into the
mounting sleeve. damage may occur.
Mounting Sleeve (Included)
Dashboard
~
. Face Plate*2 (Included)
<Mounting Hole Position>
Position B
_n~_~c
• Depending on the position chosen. thefront panel will protrude
differently.
seal (Included)
Rear
of
the Unit
@
o
It
Caution
Do not block the unit's fan or heat sink, thus preventing
air circulation.
If
blocked, heat will accumulate inside
the unit and may cause a fire.
Air
ventilation hole
Caution
concerning
the
installation
location
1 Before installing, make sure that the opening and
closing
of
the display will
not
interfere with
operation
of
the gear shift.
Movable Display
/
:'(
Frnm"~
t---
Dashboard
Position A
2
Angle
of
installation
Install at an angle
of
between horizontal and 3D·.
Note that installing at an angle outside
of
this range
will result in a loss
of
performance and possibly
damage.
'"
'"
'.
'"
3 Remove the mounting sleeve from the main
unit
(see
"Removal"
on
page 85).
The
unit
can be installed in the mounting sleeve in
three positions by aligning
its
mounting
holes (A
to
C)
on
the
sides
of
the unit. Position A will be used in
most
cases. If B
or
C are
to
be used, the hole
positions need to be modified.
First, determine the mounting position in the
mounting sleeve, then affix the supplied seal (refer
to
"How
to
use a Seal" (page 85».
Slide the
unit
into the mounting sleeve and secure it.
Front Panel
"""".,,.
'+r-.
Dashboard
Position B
;'~~l
From
'oMI
!
~?-i-
Dashboard
Position C
.1
If
the installed mounting sleeve is loose
in
the dashboard. the
pressure plates may be bent slightly to remedy the problem.
84-EN
Installation
•
If
B
or
C is used. make sure that there is a enough space depthwise
before installing the unit.
If
the unit isforcibly pushed into the
mounting sleeve. damage may occur.
Mounting Sleeve (Included)
Dashboard
~
. Face Plate*2 (Included)
<Mounting Hole Position>
Position B
_n~_~c
• Depending on the position chosen. thefront panel will protrude
differently.
seal (Included)
Rear
of
the Unit
@
o
It
Caution
Do not block the unit's fan or heat sink, thus preventing
air circulation.
If
blocked, heat will accumulate inside
the unit and may cause a fire.
Air
ventilation hole
Caution
concerning
the
installation
location
1 Before installing, make sure that the opening and
closing
of
the display will
not
interfere with
operation
of
the gear shift.
Movable Display
/
:'(
Frnm"~
t---
Dashboard
Position A
2
Angle
of
installation
Install at an angle
of
between horizontal and 3D·.
Note that installing at an angle outside
of
this range
will result in a loss
of
performance and possibly
damage.
'"
'"
'.
'"
3 Remove the mounting sleeve from the main
unit
(see
"Removal"
on
page 85).
The
unit
can be installed in the mounting sleeve in
three positions by aligning
its
mounting
holes (A
to
C)
on
the
sides
of
the unit. Position A will be used in
most
cases. If B
or
C are
to
be used, the hole
positions need to be modified.
First, determine the mounting position in the
mounting sleeve, then affix the supplied seal (refer
to
"How
to
use a Seal" (page 85».
Slide the
unit
into the mounting sleeve and secure it.
Front Panel
"""".,,.
'+r-.
Dashboard
Position B
;'~~l
From
'oMI
!
~?-i-
Dashboard
Position C
.1
If
the installed mounting sleeve is loose
in
the dashboard. the
pressure plates may be bent slightly to remedy the problem.
84-EN
To Next Page
Loading...
