How to use a Seal
If
A
is
used for installation:
Affix
the
seal
so
that mounting holes
Band
C are covered.
r-;F;~
l~
~~l
If
B
is
used for installation:
Affix
the
seal so that mounting holes A and C are covered.
If
C
is
used for installation:
Affix
the
seal
so
that the mounting holes A and B are covered.
Installing the Face Plate
;.2
If
A is used, the suppliedface plate may be mounted.
If
B is used, the face plate must be modified before installing it.
To
modify theface plate, consult your Alpine dealer.
If
C is used, the face plate cannot be mounted. Consult
your
Alpine
dealer.
4
Reinforce the head unit with the metal mounting
strap (not supplied). Secure the ground lead
of
the
unit to a clean metal spot using a screw
(*1)
already
attached to the vehicle's chassis.
•
For
the screw
marked"
*2
",
use an appropriate screw
for
the chosen
mounting location.
Connect each input lead coming from an amplifier or
equalizer to the corresponding output lead coming
from the left rear of the IVA·W505. Connect all other
leads
of
the IVA·W505 according to details
described
in
the CONNECTIONS section.
5 Slide the IVA·W505 into the dashboard until it clicks.
This ensures that the unit is properly locked and will
not accidentally come out from the dashboard.
Removal
1.
Insert the bracket keys into the unit, along the
guides
on either side. The unit can now
be
removed from the
mounting sleeve.
This unit
Bracket keys
(Included)
~~
2.
Pull the unit out, keeping it unlocked as you
do
so.
<JAPANESE CAR>
Take the face plate off, and secure the ground lead of the unit to
a clean metal spot using a screw (*) already attached to the
car's chassis.
Attach the Original Mounting Bracket to each side of the
IVA-W505, using the screws supplied with IVA-W505.
Face Plate (Included)
Mounting
Bracket
Metal
Mounting
Strap
Chassis
Screw
Ground Lead
Hex
Nut
(M5)
85-EN
How to use a Seal
If
A
is
used for installation:
Affix
the
seal
so
that mounting holes
Band
C are covered.
r-;F;~
l~
~~l
If
B
is
used for installation:
Affix
the
seal so that mounting holes A and C are covered.
If
C
is
used for installation:
Affix
the
seal
so
that the mounting holes A and B are covered.
Installing the Face Plate
;.2
If
A is used, the suppliedface plate may be mounted.
If
B is used, the face plate must be modified before installing it.
To
modify theface plate, consult your Alpine dealer.
If
C is used, the face plate cannot be mounted. Consult
your
Alpine
dealer.
4
Reinforce the head unit with the metal mounting
strap (not supplied). Secure the ground lead
of
the
unit to a clean metal spot using a screw
(*1)
already
attached to the vehicle's chassis.
•
For
the screw
marked"
*2
",
use an appropriate screw
for
the chosen
mounting location.
Connect each input lead coming from an amplifier or
equalizer to the corresponding output lead coming
from the left rear of the IVA·W505. Connect all other
leads
of
the IVA·W505 according to details
described
in
the CONNECTIONS section.
5 Slide the IVA·W505 into the dashboard until it clicks.
This ensures that the unit is properly locked and will
not accidentally come out from the dashboard.
Removal
1.
Insert the bracket keys into the unit, along the
guides
on either side. The unit can now
be
removed from the
mounting sleeve.
This unit
Bracket keys
(Included)
~~
2.
Pull the unit out, keeping it unlocked as you
do
so.
<JAPANESE CAR>
Take the face plate off, and secure the ground lead of the unit to
a clean metal spot using a screw (*) already attached to the
car's chassis.
Attach the Original Mounting Bracket to each side of the
IVA-W505, using the screws supplied with IVA-W505.
Face Plate (Included)
Mounting
Bracket
Metal
Mounting
Strap
Chassis
Screw
Ground Lead
Hex
Nut
(M5)
85-EN
To Next Page
Loading...
