Foot Brake
lead
I Parking Brake
lead
Connection
Chassis
Parking brake switch
Foot brake switch
Foot brake lamp
Parking brake lead
Foot brake lead
Pinch
Connector
(sold separately)
IVA·W505
L..-
--'
(Yellow/Blue)
,...------,
FOOT BRAKE
---
...
~~~
(Yellow/Black) Pinch
ConnectorL--------------Lo
'<:>t-----
....
PARKING BRAKE (sold
separa6te~ly
...
)--
__
__:_......I.~
....
----------_l
,
Ell
Parking brake lamp
Connection Diagram of SPST Switch (Sold Separately)
(If the ACC power supply is not available)
FUSE (5A)
(Optional)
IVA-W505
__
-If
(Red)
l
(Yellow)
IGNITION
BATTERY
1---------------,
: SPST SW (Optional) 1
1
: o"O----
......
--t
------------
1
e
Battery
•
If
your
vehicle has no
ACC
power
supply, add an
SPST
(Single-Pole, Single-Throw) switch (sold separately)
andfuse
(sold separately).
• The diagram and the
fuse
amperage shown above are in the case when IVA·W505 is usedindividually.
•
If
the switched power (ignition) lead
of
the IVA- W505 is connected directly to the positive
(+)
post
of
the vehicle's battery, the IVA- W505 draws
some current (several hundred milliamperes) even when its switch is
placed
in the
OFF
position
and
the battery may be discharged.
To
prevent
external
noise
from
entering
the
audio
system.
• Locate the unit and route the leads at least
10
cm away from the car harness.
• Keep the battery power leads as far away from other leads as possible.
• Connect the ground lead securely
to
a bare metal spot (remove any paint, dirt or grease if necessary) of the car chassis.
•
If
you
add
an optional noise suppressor, connect it as far away from the unit as possible. Your Alpine dealer carries various
noise suppressors, contact them for further information.
•
Your
Alpine dealer knows best about noise prevention measures so consult your dealer for further information.
86-EN
Foot Brake
lead
I Parking Brake
lead
Connection
Chassis
Parking brake switch
Foot brake switch
Foot brake lamp
Parking brake lead
Foot brake lead
Pinch
Connector
(sold separately)
IVA·W505
L..-
--'
(Yellow/Blue)
,...------,
FOOT BRAKE
---
...
~~~
(Yellow/Black) Pinch
ConnectorL--------------Lo
'<:>t-----
....
PARKING BRAKE (sold
separa6te~ly
...
)--
__
__:_......I.~
....
----------_l
,
Ell
Parking brake lamp
Connection Diagram of SPST Switch (Sold Separately)
(If the ACC power supply is not available)
FUSE (5A)
(Optional)
IVA-W505
__
-If
(Red)
l
(Yellow)
IGNITION
BATTERY
1---------------,
: SPST SW (Optional) 1
1
: o"O----
......
--t
------------
1
e
Battery
•
If
your
vehicle has no
ACC
power
supply, add an
SPST
(Single-Pole, Single-Throw) switch (sold separately)
andfuse
(sold separately).
• The diagram and the
fuse
amperage shown above are in the case when IVA·W505 is usedindividually.
•
If
the switched power (ignition) lead
of
the IVA- W505 is connected directly to the positive
(+)
post
of
the vehicle's battery, the IVA- W505 draws
some current (several hundred milliamperes) even when its switch is
placed
in the
OFF
position
and
the battery may be discharged.
To
prevent
external
noise
from
entering
the
audio
system.
• Locate the unit and route the leads at least
10
cm away from the car harness.
• Keep the battery power leads as far away from other leads as possible.
• Connect the ground lead securely
to
a bare metal spot (remove any paint, dirt or grease if necessary) of the car chassis.
•
If
you
add
an optional noise suppressor, connect it as far away from the unit as possible. Your Alpine dealer carries various
noise suppressors, contact them for further information.
•
Your
Alpine dealer knows best about noise prevention measures so consult your dealer for further information.
86-EN
To Next Page
Loading...
