CD
Radio Antenna Receptacle
@ S Video Input Connector
Input the video signal.
Connect to the output terminal of S video of connected
devices.
@ Video Input Connector (AUX INPUT) (Yellow)
Input the video.
@ Audio Input Connectors (AUX INPUT)
RED
is
right and WHITE
is
left input the audio.
@ Video Output Connector (AUX OUTPUT) (Yellow)
Output the video.
® Audio Output Connectors (AUX OUTPUT)
RED
is right and WHITE
is
left output the audio.
(j)
Remote Control Output Lead (WhitelBrown)
Connect this lead to the remote control input lead. This lead
outputs the controlling signals from the remote control.
@ Remote Control
Input
Lead (White/Brown)
Connect the external Alpine product
to
the remote control
output lead.
® Reverse Lead (OrangelWhite)
Use only when a back-up camera
is
connected. Connect to
the plus side of the car's reverse lamp. This lamp illuminates
when the transmission
is
shifted into reverse
(R).
With this lead properly wired, the video picture
automatically switches to the back-up camera whenever the
car is put into reverse (R).
@ Monitor Control Lead (WhitelPink)
Connect this to the Monitor Control Lead of the touch panel-
compatible rear monitor.
@ USB Connector
@ AUX
110
Camera In Connector
@ FULL
SPEEDTM
Connection Cable (KCE-422i) (sold
separately)
@ GPS Antenna Receptacle
To
GPS
Antenna (sold separately).
@ Steering Remote Control Interface Connector
To
steering remote control interface box.
For details about connections, consult your nearest Alpine
dealer.
@ iPod Direct Connector
iPod control signals.
Connect this to
an
iPod or
an
optional Bluetooth Box, using
the FULL
SPEEDTM
Connection Cable (KCE-422i) (sold
separately).
To
use a hands-free mobile phone, an optional Bluetooth
Box connection is required. For details on connection, refer
to
the Owner's Manual of the Bluetooth Box.
@ CAMERA Input Connector
Use when connecting a back-up camera.
@ RGB Input Terminal
Connect this to the
RGB
output terminal of the Navigation
System.
@l
TMC Antenna Receptacle
To
TMC Antenna (sold separately).
@ Digital Output Terminal (Optical)
Use when combining fiber optic digital input compatible
products. Be sure to use the Optical Digital Cable (KWE-
610A) (sold separately) only.
88-EN
® Ai-NET Connector
Connect this to the output or input connector of another
device (CD Changer, Equalizer, HD
Radio™
TUNER
MODULE, etc.) equipped with
Ai-NET.
•
You
can input TV/video sound by connecting an optional
Ai-NET/RCA Interface cable (KCA-12IB) to this component.
@ Rear Outputllnput RCA Connectors
It can be used as Rear Output or Input
RCA
Connectors.
@ Front Outputllnput RCA Connectors
It
can be used as Front Output
or
Input
RCA
Connectors.
@ Subwoofer RCA Connectors
RED
is right and WHITE is left.
@ System Switch
When connecting an equalizer or divider using Ai-NET
feature, place the two switches
in
the EQ/DIV position.
When no device
is
connected, leave the switches
in
the
NORM position.
• Do not make the two switches
ro
different settings.
•
Be
sure to
tum
the power
off
to the unit before changing
rhe
swirch
position.
@ Power Supply Connector
® Ai-NET Cable (InclUded with CD Changer)
@ Remote Turn-On Lead (BluelWhlte)
Connect this lead to the remote turn-on lead of your
amplifier or signal processor.
@ Power Antenna Lead (Blue)
Connect this lead to the +B terminal of your power antenna,
if applicable.
• This lead should
be
used only
for
controlling the vehicle's power
antenna. Do not use this lead
to
rum on an amplifier
or
a signal
processor, etc.
@ Audio Interrupt In Lead (Pink/Black)
® Parking Brake Lead (YellowlBlue)
Connect this lead to the power supply side of the parking
brake switch to transmit the parking brake status signals to
the IVA-W505.
@ Foot Brake Lead (YellowlBlack)
Connect to the vehicle's foot brake lead or brake lamp lead.
@ Switched Power Lead (Ignition) (Red)
Connect this lead to
an
open terminal on the vehicle's fuse
box or another unused power source which provides (+)
12V only when the ignition is turned
on
or
in
the accessory
position.
® Battery Lead (Yellow)
Connect this lead to the positive
(+)
post of the vehicle's
battery.
@ Fuse Holder
(1
OA)
CD
Radio Antenna Receptacle
@ S Video Input Connector
Input the video signal.
Connect to the output terminal of S video of connected
devices.
@ Video Input Connector (AUX INPUT) (Yellow)
Input the video.
@ Audio Input Connectors (AUX INPUT)
RED
is
right and WHITE
is
left input the audio.
@ Video Output Connector (AUX OUTPUT) (Yellow)
Output the video.
® Audio Output Connectors (AUX OUTPUT)
RED
is right and WHITE
is
left output the audio.
(j)
Remote Control Output Lead (WhitelBrown)
Connect this lead to the remote control input lead. This lead
outputs the controlling signals from the remote control.
@ Remote Control
Input
Lead (White/Brown)
Connect the external Alpine product
to
the remote control
output lead.
® Reverse Lead (OrangelWhite)
Use only when a back-up camera
is
connected. Connect to
the plus side of the car's reverse lamp. This lamp illuminates
when the transmission
is
shifted into reverse
(R).
With this lead properly wired, the video picture
automatically switches to the back-up camera whenever the
car is put into reverse (R).
@ Monitor Control Lead (WhitelPink)
Connect this to the Monitor Control Lead of the touch panel-
compatible rear monitor.
@ USB Connector
@ AUX
110
Camera In Connector
@ FULL
SPEEDTM
Connection Cable (KCE-422i) (sold
separately)
@ GPS Antenna Receptacle
To
GPS
Antenna (sold separately).
@ Steering Remote Control Interface Connector
To
steering remote control interface box.
For details about connections, consult your nearest Alpine
dealer.
@ iPod Direct Connector
iPod control signals.
Connect this to
an
iPod or
an
optional Bluetooth Box, using
the FULL
SPEEDTM
Connection Cable (KCE-422i) (sold
separately).
To
use a hands-free mobile phone, an optional Bluetooth
Box connection is required. For details on connection, refer
to
the Owner's Manual of the Bluetooth Box.
@ CAMERA Input Connector
Use when connecting a back-up camera.
@ RGB Input Terminal
Connect this to the
RGB
output terminal of the Navigation
System.
@l
TMC Antenna Receptacle
To
TMC Antenna (sold separately).
@ Digital Output Terminal (Optical)
Use when combining fiber optic digital input compatible
products. Be sure to use the Optical Digital Cable (KWE-
610A) (sold separately) only.
88-EN
® Ai-NET Connector
Connect this to the output or input connector of another
device (CD Changer, Equalizer, HD
Radio™
TUNER
MODULE, etc.) equipped with
Ai-NET.
•
You
can input TV/video sound by connecting an optional
Ai-NET/RCA Interface cable (KCA-12IB) to this component.
@ Rear Outputllnput RCA Connectors
It can be used as Rear Output or Input
RCA
Connectors.
@ Front Outputllnput RCA Connectors
It
can be used as Front Output
or
Input
RCA
Connectors.
@ Subwoofer RCA Connectors
RED
is right and WHITE is left.
@ System Switch
When connecting an equalizer or divider using Ai-NET
feature, place the two switches
in
the EQ/DIV position.
When no device
is
connected, leave the switches
in
the
NORM position.
• Do not make the two switches
ro
different settings.
•
Be
sure to
tum
the power
off
to the unit before changing
rhe
swirch
position.
@ Power Supply Connector
® Ai-NET Cable (InclUded with CD Changer)
@ Remote Turn-On Lead (BluelWhlte)
Connect this lead to the remote turn-on lead of your
amplifier or signal processor.
@ Power Antenna Lead (Blue)
Connect this lead to the +B terminal of your power antenna,
if applicable.
• This lead should
be
used only
for
controlling the vehicle's power
antenna. Do not use this lead
to
rum on an amplifier
or
a signal
processor, etc.
@ Audio Interrupt In Lead (Pink/Black)
® Parking Brake Lead (YellowlBlue)
Connect this lead to the power supply side of the parking
brake switch to transmit the parking brake status signals to
the IVA-W505.
@ Foot Brake Lead (YellowlBlack)
Connect to the vehicle's foot brake lead or brake lamp lead.
@ Switched Power Lead (Ignition) (Red)
Connect this lead to
an
open terminal on the vehicle's fuse
box or another unused power source which provides (+)
12V only when the ignition is turned
on
or
in
the accessory
position.
® Battery Lead (Yellow)
Connect this lead to the positive
(+)
post of the vehicle's
battery.
@ Fuse Holder
(1
OA)
To Next Page
Loading...
