Altronix 6062 Installation Guide

- 2 - 6062
Altronix is not responsible for any typographical errors.
140 58th Street, Brooklyn, New York 11220 USA | phone: 718-567-8181 | fax: 718-567-9056
website: www.altronix.com | e-mail: info@altronix.com | Lifetime Warranty | Made in U.S.A.
II6062 - Rev. 032211 L01Q
MEMBER
6062 Typical Applications:
For this application Switch #1 and Switch #4
should be in the OFF position.
For this application Switch #1 should be in the OFF
position and Switch #4 should be in the ON position.
Fig. 2 - Guard Tour Supervisory Timer: Fig. 6 - Timed Shunt for a Door: Use to bypass alarm contacts.
TRG -- +
Closed
Circuit
Contact
Pull up
Resistor
Power
Supply
+
---
TRG -- +NOCNC
1
ON
ON
1 2 3 4
OFF
15
CUT J3 FOR RESET ON POWER-UP
TRIG CONTROL
12V / 24V
SEC. / MIN.
RELAY CONTROL
CHIME
Pos (+) and Neg (--
)
terminals constant
12VDC or 24VDC
Normally Open
Door Contacts
+
---
+
---
4 3 2 1
J3
CUT J2 FOR DELAY PULSE J2 CUT J1 FOR REPEAT J1
45
60
TRG -- +NOCNC
1
ON
ON
1 2 3 4
OFF
15
CUT J3 FOR RESET ON POWER-UP
TRIG CONTROL
12V / 24V
SEC. / MIN.
RELAY CONTROL
Pos (+) and Neg (--
)
terminals constant
12VDC or 24VDC
Normally Open
Door Contacts
Door Strike
+
---
+ ---
4 3 2 1
J3
CUT J2 FOR DELAY PULSE J2 CUT J1 FOR REPEAT J1
45
60
TRG -- +NOCNC
1
ON
ON
1 2 3 4
OFF
15
CUT J3 FOR RESET ON POWER-UP
TRIG CONTROL
12V / 24V
SEC. / MIN.
RELAY CONTROL
DIALER OR
TRANSMITTER
Pos (+) and Neg (-- )
terminals constant
12VDC or 24VDC
Normally Open
Switch Contacts
+
---
4 3 2 1
J3
CUT J2 FOR DELAY PULSE J2 CUT J1 FOR REPEAT J1
45
60
TRG -- +NOCNC
1
ON
ON
1 2 3 4
OFF
15
CUT J3 FOR RESET ON POWER-UP
TRIG CONTROL
12V / 24V
SEC. / MIN.
RELAY CONTROL
Pos (+) and Neg (--
)
terminals constant
12VDC or 24VDC
Door Contacts
Protective
Circuit
+
---
4 3 2 1
J3
CUT J2 FOR DELAY PULSE J2 CUT J1 FOR REPEAT J1
45
60
Normally Open
Switch Contacts
TRG -- +NOCNC
1
ON
ON
1 2 3 4
OFF
15
CUT J3 FOR RESET ON POWER-UP
TRIG CONTROL
12V / 24V
SEC. / MIN.
RELAY CONTROL
Closed
Circuit
Zone on
Control Panel
Pos (+) and Neg (--
)
terminals constant
12VDC or 24VDC
Protective
Circuit
+
---
4 3 2 1
J3
CUT J2 FOR DELAY PULSE J2 CUT J1 FOR REPEAT J1
45
60
TRG -- +NOCNC
1
ON
ON
1 2 3 4
OFF
15
CUT J3 FOR RESET ON POWER-UP
TRIG CONTROL
12V / 24V
SEC. / MIN.
RELAY CONTROL
Use appropriate contacts
to reporting devices
Normally Open
Triggering Device
Pos (+) and Neg (--
)
terminals constant
12VDC or 24VDC
+
---
4 3 2 1
J3
CUT J2 FOR DELAY PULSE J2 CUT J1 FOR REPEAT J1
45
60
TRG -- +NOCNC
1
ON
ON
1 2 3 4
OFF
15
CUT J3 FOR RESET ON POWER-UP
TRIG CONTROL
12V / 24V
SEC. / MIN.
RELAY CONTROL
Bell
or
Siren
+
---
4 3 2 1
J3
CUT J2 FOR DELAY PULSE J2 CUT J1 FOR REPEAT J1
45
60
Bell
Output
Control Panel
12VDC or 24VDC
Fig. 1 - Timed Door Annunciator: Fig. 5 - Timed Door Strike:
For this application Switch #1 and Switch #4
should be in the OFF position.
For this application Switch #1 should be in the OFF
position and Switch #4 should be in the ON position.
Fig. 3 - Swinger Eliminator: Fig. 7 - Bell Cut Off Timer:
For this application Switch #1 should be in the OFF position
and Switch #4 should be in the ON position.
For this application Switch #1 should be in the ON position
and Switch #4 is not used in this application.
Fig. 4 - Delay Timer: Use for Door Ajar Alarm, Delayed
Activation of Digital Dialer, Defrost Cycle Timer, etc...
Fig. 8 - Closed Circuit Trigger Option:
For this application Switch #1 should be in the ON
position and Switch #4 is not used in this application.
For this application a resistor [for 12VDC - 2K (2,000 ohm)
or for 24VDC - 4.7K (4,700 Ohm)] must be installed as
shown (resistor not supplied).

Altronix 6062 Specifications

General

Timer type	-
Product color	Blue
Number of modules	1
AC input voltage	24 V