American Lighting TRULUX TWRF-3AAA

To Next Page

SAFETY INFORMATION

• Read all instructions before beginning; Save these instructions for future use.

• To reduce the risk of ﬁre, electric shock, or injury to persons, pay close attention

to this manual and stay within its guidelines when using this product.

• This controller is rated IP20; avoid the sun and moisture.

• Avoid using controller in areas where extreme hot, cold, dust, or humidity exist.

• This controller is suitable for indoor, dry locations only.

• Always be sure to store this controller in an area with proper ventilation to

avoid overheating.

These products may represent a possible shock or

ﬁre hazard if improperly installed or attached in any

way. Products should be installed in accordance

with these instructions, current electrical codes,

and/or the current National Electric Code (NEC).

This controller is battery operated and requires

3x AAA batteries (not included).

Page 1 of 2 11775 E. 45th Ave. Denver, CO 80239 Ph: 1-800-880-1180 Fax: 303-695-7633

WARNING

TRULUX RF Tunable Remote Control

INSTALLATION INSTRUCTIONS

TWRF-3AAA

BATTERY

OPERATED

SYNCING CONTROLLER TO RECEIVER (SEE FIGURES 1 & 2):

This controller is battery operated and requires

3x AAA batteries (not included).

This controller requires a Radio Frequency receiver for

operation (REC-5A-4Z or REC-5A-4Z-WiFi sold separately).

1. Press the power button on the controller once to turn on power

to the controller.

2. Press the “Learning Key” on the receiver.

3. Select a zone by pressing one of the four zone buttons on the

controller, then touch color temperature wheel to activate controller.

4. Once successfully synced, the connected light source will blink.

5. Repeat steps 2-3 when syncing multiple receivers to a single

controller.

6. Press and hold the “Learning Key” to clear out saved sync data

when wanting to reset scenes or zones.

FIGURE 1

FIGURE 2

OPERATING CONTROLLER (SEE FIGURE 2):

This controller is battery operated and requires

3x AAA batteries (not included).

1. Press power button in center of remote for On/O power control.

The power indicator light will turn on when remote is awake.

2. Touch and slide the color temperature wheel for cool to warm

CCT control.

3. Press and hold brightness button in center of color temperature

wheel for up/down 1-100% brightness control.

4. Press the pre-set brightness buttons for 15%, 25%, 50%, or 100%

pre-set brightness levels.

5. To select a zone, press one of the four zone buttons once. Memory

can select multiple zones simultaneously.

6. To save a scene, determine desired settings, press and hold

scene button for 2 seconds. Memory will hold 3 scenes per zone.

7. To select a scene, press one of the three scene buttons once.

CARE AND MAINTENANCE:

1. For cleaning, use a soft, dry or damp cloth. Do not use harsh chemicals or abrasives.

2. This controller is battery operated and requires 3x AAA batteries (not included). If swallowed, batteries could cause severe injury or death. Seek

medical attention immediately. Non-rechargeable batteries are not to be recharged. Remove exhausted batteries from the product; Please

dispose of batteries properly. Do not dispose of batteries in ﬁre; Batteries may explode or leak.

Power

Indicator light

Brightness

Color Temperature

Wheel

Zones 1-4

Scenes 1-3

Pre-set 50%

Brightness

Pre-set 25%

Brightness

Power (On/O )

Pre-set 15%

Brightness

Pre-set 100%

Brightness

SR-1009FA

LED CONTROLLER

INPUT

12-36V DC

PRI

SEC

Learning Key

MASTER SLAVE

° tc=75°C

150805V1

PRI:

Uin=12-36VDC

Iin=20.5A

SEC:

Uout=4x(12-36)VDC

Iout=4x5A

Pout=4x(60-180)W

TEMP RANGE:-20°C-+50°C

6-7mm

0.5-1.5mm

Trulux RF Receiver

(sold separately)

To 12-24V DC

Power Supply

Learning Key

RF Controller “talks” to the receiver via a

wireless Radio Frequency (RF) signal

Need help?

Do you have a question about the American Lighting TRULUX TWRF-3AAA and is the answer not in the manual?

The TRULUX RF Tunable Remote Control is a battery-operated device designed for controlling LED lighting systems. It functions as a remote control for tunable white lighting, allowing users to adjust color temperature and brightness. The device requires 3x AAA batteries for operation (not included) and communicates wirelessly via Radio Frequency (RF) signals with a compatible RF receiver (e.g., REC-5A-4Z or REC-5A-4Z-WiFi, sold separately).

Safety Information:

The product is rated IP20, meaning it is protected against solid objects larger than 12.5mm but has no protection against liquids. It is suitable for indoor, dry locations only and should be kept away from direct sunlight, moisture, extreme hot or cold temperatures, dust, and humidity. Proper ventilation is required to prevent overheating. Installation should adhere to current electrical codes and the National Electric Code (NEC) to avoid potential shock or fire hazards.

Function Description:

The remote control allows users to:

Power On/Off: Turn the connected lighting system on or off.
Color Temperature Adjustment: Adjust the color temperature from cool to warm CCT (Correlated Color Temperature) using a touch-sensitive wheel.
Brightness Control: Adjust brightness levels from 1% to 100% using a dedicated button or pre-set buttons.
Zone Control: Select and control up to four independent lighting zones. Multiple zones can be selected simultaneously.
Scene Saving and Recall: Save up to three custom lighting scenes per zone and recall them with a single button press.

Technical Specifications:

Power Source: 3x AAA batteries (not included).
Communication: Radio Frequency (RF) wireless signal.
Compatibility: Requires a compatible RF receiver (e.g., SR-1009FA LED CONTROLLER, REC-5A-4Z, or REC-5A-4Z-WiFi).
IP Rating: IP20.
Operating Environment: Indoor, dry locations only. Avoid extreme temperatures, dust, and humidity.
FCC Compliance: The device complies with Part 15 of the FCC Rules, ensuring it does not cause harmful interference and accepts any interference received.

Usage Features:

Syncing Controller to Receiver:

Press the power button on the controller to turn it on.
Press the "Learning Key" on the receiver.
Select a desired zone by pressing one of the four zone buttons on the controller.
Touch the color temperature wheel on the controller to activate it.
The connected light source will blink, indicating successful syncing.
Repeat steps 2-3 to sync multiple receivers to a single controller.
To clear saved sync data and reset scenes or zones, press and hold the "Learning Key" on the receiver.

Operating Controller:

Power On/Off: Press the power button in the center of the remote. The power indicator light will illuminate when the remote is active.
Color Temperature: Touch and slide the color temperature wheel to adjust CCT from cool to warm.
Brightness: Press and hold the brightness button (in the center of the color temperature wheel) for continuous 1-100% brightness control.
Pre-set Brightness: Use the dedicated buttons for 15%, 25%, 50%, or 100% pre-set brightness levels.
Zone Selection: Press one of the four zone buttons once to select a zone. Multiple zones can be selected simultaneously.
Scene Saving: Determine desired lighting settings, then press and hold a scene button (S1, S2, or S3) for 2 seconds. The controller can store up to three scenes per zone.
Scene Recall: Press one of the three scene buttons once to recall a saved scene.

Maintenance Features:

Cleaning: Use a soft, dry, or damp cloth for cleaning. Avoid harsh chemicals or abrasives.
Battery Handling:
- The controller requires 3x AAA batteries.
- Non-rechargeable batteries should not be recharged.
- Remove exhausted batteries promptly.
- Dispose of batteries properly; do not dispose of them in fire, as they may explode or leak.
- If batteries are swallowed, seek immediate medical attention as they can cause severe injury or death.