Apator Metra E-ITN 30 User Manual

E-ITN 30
user guide 2015/11d [EN]
To save the battery, after longer period of inactivity (approx.
1 min.), energy-saving mode is activated and display is
switched off. Display can be activated by pushing the
button.
When pushing the button briefly, notice ----- on the display
will appear. If the button is not pushed in 1 minute, the
display will switch off.
Displayed data
E-ITN 30.2, E-ITN 30.4
Value for current billing period 245
Value for last billing period 458 SM
Alphanumerical code for last billing period A.0.i.h.t.
Serial number – first part -3400
Serial number – second part 0060-
E-ITN 30.3
LCD test
Current date 10.12.
Start of the billing period u 1.2.
Value for last billing period 458 SM
Alphanumerical code A.0.i.h.t.
Average surroundings temperature for last
billing period
23.7°C SM
Value for current billing period 245
E-ITN 30.5, E-ITN 30.51 Wireless M-Bus
LCD test
Current date 10.12.
Start of the billing period u 1.2.
Value for last billing period 458 SM
Average surroundings temperature for last
billing period
23.7°C SM
Value for current billing period 245
E-ITN 30.6 Wireless M-Bus
Value for current year billing period 245
Value for last year billing period 458 SM
Value for current month billing period 2.4.5
Value for last month billing period .4.5.8.SM
Serial number – first part -3400
Serial number – second part 0060-
* also other items can be displayed based on setting
Transport and storage
Transport
• devices can be transported by all usual covered means
of transport
• devices must be in original package
• originally packed devices must be stored and secured
to avoid mechanical damages during transportation
• devices can not be transported together with
aggressive substances
• temperature during transportation from -10 °C to +50
°C
• relative humidity from 45 % to 75 %
Storage
• devices must be originally packed by manufacturer and
individually stored in antistatic bags
• storage temperature from +10 °C to +30 °C
• relative humidity from 45 % to 75 %
• devices must be stored in clean covered areas without
aggressive substances and stored properly to avoid
mechanical damage
Disposal
This device is subject to a waste management in
accordance with local legislation.
Possible minor faults and their elimination
Any E-ITN 30 defect should be repaired by manufacturer
only.
Warranty terms and conditions
If device is installed and handled according to manufacturer
instructions mentioned in Installation and service manual,
manufacturer provide warranty under the valid legislation
unless agreed differently.
The warranty is void if device was used contrary to
Installation and service manual or damaged:
• during transport or storage by customer or reseller
• when mounted or dismantled to the customer device
• because of improper handling or installation into other
device than agreed in manual
• if the product was exposed to different environment
than agreed in manual
• if mechanically or in other way damaged by user
Declaration of conformity, declaration of directive RoHS
You can find declaration of conformity and declaration of
directive RoHS on producer´s web page:
www.metra-su.cz
Warranty and post warranty repairs
Warranty and post warranty repairs have to be done by
manufacturer. Pack the defective product and send
back to the address:
APATOR METRA s.r.o.
Havlíčkova 919/24
787 64 Šumperk
Czech republic
Tel.: 583 718 263
Fax: 583 718 150
E-mail: prodej@metra - su.cz
www: http://www.metra - su.cz
2 / 2

Apator Metra E-ITN 30 Specifications

General

Brand	Apator Metra
Model	E-ITN 30
Category	Control Unit
Language	English