Arcam Solo movie 2.1 - Before You Begin; Placing the Unit and Power

Arcam (A&R Cambridge Ltd), Pembroke Avenue, Waterbeach, CAMBRIDGE, CB25 9QR, England
+44 (0)1223 203200 www.arcam.co.uk/extranet
RS232
(solo movie)
6
Treble
Change the treble level.
Example
Command/response sequence to set the treble, where the new level is -6dB:
COMMAND: 0x21 0x01 0x06 0x01 0x5E 0x0D
RESPONSE: 0x21 0x01 0x06 0x01 0x01 0x5E 0x0D
Byte: Description:
ZN 0x01 (Zone)
CC 0x06 (Command code)
NB 0x01 (Number of bytes)
DATA 0x5D = -7
…
0x64 = 0
…
0x6B = +7
0xF0 = Query
Bass correction
Change the bass correction level.
Example
Command/response sequence to turn bass correction off:
COMMAND: 0x21 0x01 0x07 0x01 0x00 0x0D
RESPONSE: 0x21 0x01 0x07 0x01 0x01 0x00 0x0D
Byte: Description:
ZN 0x01 (Zone)
CC 0x07 (Command code)
NB 0x01 (Number of bytes)
DATA 0x00 = Bass correction Off
…
0x03 = Bass correction Max
0xF0 = Query.
Sub level
Change the sub level.
Example
Command/response sequence to set the sub level, where the new level is +5db:
COMMAND: 0x21 0x01 0x17 0x01 0x0F 0x0D
RESPONSE: 0x21 0x01 0x17 0x01 0x01 0x0F 0x0D
Byte: Description:
ZN 0x01 (Zone)
CC 0x17 (Command code)
NB 0x01 (Number of bytes)
DATA 0x00 = -10
…
0x0A = 0
…
0x14 = +10
0xF0 = Query
Mute
Mute the output.
Example
Command/response sequence to set the mute state of Zone 1, where the result is that the
output is muted:
COMMAND: 0x21 0x01 0x08 0x01 0x01 0x0D
RESPONSE: 0x21 0x01 0x08 0x01 0x01 0x01 0x0D
Byte: Description:
ZN 0x01 (Zone 1)
0x02 (Zone 2)
CC 0x08 (Command code)
NB 0x01 (Number of bytes)
DATA 0x00 = Mute Off
0x01 = Mute On
0xF0 = Query
Preset mode/Preset select
Command/response sequence to query the unit for the current preset mode, to toggle the
preset mode, or load a stored preset.
Example
Command/response sequence to query the current preset mode, where the result is Tune
mode with preset number 5 loaded:
COMMAND: 0x21 0x01 0x13 0x01 0xF0 0x0D
RESPONSE: 0x21 0x01 0x13 0x01 0x02 0x00 0x05 0x0D
Byte: Description:
ZN 0x01 (Zone)
CC 0x13 (Command code)
NB 0x01 (Number of bytes)
DATA 0x01 … 0x1E = Preset number to load
0xF0 = Query mode
0xF3 = Toggle mode
RESPONSE
Byte: Description:
ZN 0x01 (Zone)
RC 0x13 (Reply Code)
AC 0x01 (Answer code)
NB 0x02 (Number of bytes)
D1 0x00 = Tune mode
0x01 = Preset mode
D2 Current preset number
Display brightness
Set the display brightness.
Example
Command/response sequence to set the display brightness, where the result is that the display
brightness is at level 1:
COMMAND: 0x21 0x01 0x0A 0x01 0x01 0x0D
RESPONSE: 0x21 0x01 0x0A 0x01 0x01 0x01 0x0D
Byte: Description:
ZN 0x01 (Zone)
CC 0x0A (Command code)
NB 0x01 (Number of bytes)
DATA 0x00 = Display Off
…
0x04 = Display full brightness
0xF0 = Query