Arcam Solo movie 2.1 - Product Overview; Introduction to Solo

Arcam (A&R Cambridge Ltd), Pembroke Avenue, Waterbeach, CAMBRIDGE, CB25 9QR, England
+44 (0)1223 203200 www.arcam.co.uk/extranet
RS232
(solo movie)
7
Stand-by display brightness
Set the Stand-by display brightness.
Example
Command/response sequence to set the display brightness, where the result is that the display
brightness is at level 1:
COMMAND: 0x21 0x01 0x16 0x01 0x01 0x0D
RESPONSE: 0x21 0x01 0x16 0x01 0x01 0x01 0x0D
Byte: Description:
ZN 0x01 (Zone)
CC 0x16 (Command code)
NB 0x01 (Number of bytes)
DATA 0x00 = Display Off
…
0x04 = Display full brightness
0xF0 = Query
‘Snooze’ time
Set the ‘snooze’ time (when applicable).
Example
Command/response sequence to set the snooze time to 90 minutes:
COMMAND: 0x21 0x01 0x29 0x01 0x5A 0x0D
RESPONSE: 0x21 0x01 0x29 0x01 0x01 0x5A 0x0D
Byte: Description:
ZN 0x01 (Zone)
CC 0x29 (Command code)
NB 0x01 (Number of bytes)
DATA 0x00 = Off
0x01 = 1 minute
…
0x5A = 90 minutes
0xF0 = Query
‘Sleep’ time
Set the ‘sleep’ time.
Example
Command/response sequence to set the sleep time to 120 minutes:
COMMAND: 0x21 0x01 0x31 0x01 0x78 0x0D
RESPONSE: 0x21 0x01 0x31 0x01 0x01 0x78 0x0D
Byte: Description:
ZN 0x01 (Zone)
CC 0x31 (Command code)
NB 0x01 (Number of bytes)
DATA 0x00 = Off
0x01 = 1 minute
…
0x78 = 120 minutes
0xF0 = Query
Headphones
Determine whether headphones are connected to Solo Movie.
Example
Command/response sequence to request the headphone status, where the headphones are not
connected:
COMMAND: 0x21 0x01 0x32 0x01 0xF0 0x0D
RESPONSE: 0x21 0x01 0x32 0x01 0x01 0x00 0x0D
Byte: Description:
ZN 0x01 (Zone)
CC 0x32 (Command code)
NB 0x01 (Number of bytes)
DATA 0xF0 = Query
RESPONSE
Byte: Description:
ZN 0x01 (Zone)
RC 0x32 (Reply Code)
AC 0x01 (Answer code)
NB 0x01 (Number of bytes)
DATA 0x00 = No headphones
0x01 = Headphones connected
Request tuner module type
Determine the tuner module type present in Solo Movie.
Example
Command/response sequence to request the tuner module type, where the type is DAB/FM:
COMMAND: 0x21 0x01 0x37 0x01 0xF0 0x0D
RESPONSE: 0x21 0x01 0x37 0x01 0x01 0x00 0x0D
Byte: Description:
ZN 0x01 (Zone)
CC 0x37 (Command code)
NB 0x01 (Number of bytes)
DATA 0xF0 = Query
RESPONSE
Byte: Description:
ZN 0x01 (Zone)
RC 0x37 (Reply Code)
AC 0x01 (Answer code)
NB 0x01 (Number of bytes)
DATA 0x00 = DAB/FM module tted
0x01 = AM/FM module tted