Asus P5WDG2 WS Professional - Disk Drives

ASUS P5WDG2 WS ProfessionalASUS P5WDG2 WS Professional
ASUS P5WDG2 WS ProfessionalASUS P5WDG2 WS Professional
ASUS P5WDG2 WS Professional
2-332-33
2-332-33
2-33
• These connectors are set to
Standard IDE Standard IDE
Standard IDE Standard IDE
Standard IDE mode by default. In
SS
SS
S
tandard IDE tandard IDE
tandard IDE tandard IDE
tandard IDE mode, you can connect Serial ATA boot/data hard
disk drives to these connectors. If you intend to create a Serial ATA
RAID set using these connectors, set the
Configure SATA AsConfigure SATA As
Configure SATA AsConfigure SATA As
Configure SATA As
item in the BIOS to [RAID]. See section “4.3.6 IDE Configuration” for
details.
• For RAID 5, use at least three hard disk drives. For RAID 10, use at
least four hard disk drives. Use two to four Serial ATA hard disk
drives for each RAID 0 or RAID 1 set.
3.3.
3.3.
3.
ICH7R Serial ATA connectors (7-pin SATA1 [red],ICH7R Serial ATA connectors (7-pin SATA1 [red],
ICH7R Serial ATA connectors (7-pin SATA1 [red],ICH7R Serial ATA connectors (7-pin SATA1 [red],
ICH7R Serial ATA connectors (7-pin SATA1 [red],
SATA2 [red], SATA3 [black], SATA4 [black])SATA2 [red], SATA3 [black], SATA4 [black])
SATA2 [red], SATA3 [black], SATA4 [black])SATA2 [red], SATA3 [black], SATA4 [black])
SATA2 [red], SATA3 [black], SATA4 [black])
These connectors are for Serial ATA signal cables for Serial ATA hard
disk drives.
If you installed Serial ATA hard disk drives, you can create a RAID 0,
RAID 1, RAID 10, and RAID 5 configuration with the Intel
®
Matrix
Storage Technology through the onboard Intel
®
ICH7R RAID controller.
P5WDG2-WS PRO
®
P5WDG2-WS PRO SATA connectors
SATA1
SATA4 SATA3
SATA2
GND
SATA_TXP0
SATA_TXN0
GND SATA_RXN0
SATA_RXP0
GND
GND
SATA_TXP1
SATA_TXN1
GND SATA_RXN1
SATA_RXP1
GND
GND
SATA_TXP2
SATA_TXN2
GND SATA_RXN2
SATA_RXP2
GND
GND
SATA_TXP3
SATA_TXN3
GND SATA_RXN3
SATA_RXP3
GND
If any device jumper is set as "Cable-Select," make sure all other device
jumpers have the same setting.
Black or gray
Drive jumperDrive jumper
Drive jumperDrive jumper
Drive jumper
ModeMode
ModeMode
Mode
CableCable
CableCable
Cable
settingsetting
settingsetting
setting
of device(s)of device(s)
of device(s)of device(s)
of device(s)
connectorconnector
connectorconnector
connector
Single device Cable-Select or Master - Black
Two devices Cable-Select Master Black
Slave Gray
Master Master
Slave Slave