Telephone operation
Operation Steps
Making a call Using a cordless handset:
Press PHONE or /SPEA�ERSPEA�ER -> Enter the telephone number.
Using the telephone base:
Press /SPEA�ERSPEA�ER or lift the corded handset -> Enter the
telephone number.
Answering a call Using a cordless handset:
Press PHONE or /SPEA�ERSPEA�ER, or press any dialing key
(0-9, TONE or #).
Using the telephone base:
Press /SPEA�ERSPEA�ER, or lift the corded handset.
Ending a call Using a cordless handset:
Press OFF or return the handset to the charger.
Using the telephone base:
Press /SPEA�ERSPEA�ER or hang up the corded handset.
Handset
speakerphone
During a call, press /SPEA�ERSPEA�ER to switch between
handsfree speakerphone and normal handset use.
Redial Using a cordless handset:
Press REDIAL repeatedly to select the desired entry
-> PHONE or /SPEA�ERSPEA�ER to call.
Using the telephone base:
Press REDIAL repeatedly to select the desired entry
-> press /SPEA�ERSPEA�ER or lift the corded handset to call.
Volume control
On the telephone base, press VOLUMEq to decrease or
press VOLUMEp to increase the listening volume during a
call. On a cordless handset, press q or p.
Call waiting
(Requires subscription
from telephone
service provider)
Press FLASH on the handset or FLASH on the telephone
base to put current call on hold and to take the new call;
press again to switch back and forth between calls.
Caller ID
This product supports caller ID services offered by most telephone service providers.
The telephone stores caller ID information of the last 50 incoming calls in the
telephone base. This information is common to all devices.
Missed call indicator
When a handset or the telephone base is in idle mode and has new or missed
calls, its screen shows XX Missed calls.
You can erase the missed call indicator either by reviewing the call log one by
one, or by pressing and holding CANCEL on the handset or CANCEL on the
telephone base in idle mode.
Review and dial a number in the call log
1. CID in idle mode -> q or p to scroll through the list.
2. When the desired entry is displayed, press PHONE or /SPEA�ER on the
cordless handset to call. On the telephone base, lift the corded handset or
press /SPEA�ER to call.
Caller ID announce
When this feature is on and you have an incoming call, the handset and/or
base speaks “Call from...” and the name of the caller based on the directory
or caller ID information. You can turn this feature off for the base or each
individual handset, or for all devices.
1. MENU -> q or p -> Settings -> SELECT.
2. q or p -> Caller ID annc -> SELECT.
3. q or p to choose the desired option, then pressthe desired option, then press MENU/SELECT.
Set all On/Off - Change the setting for the base and all handsets.
Local handset - Change the setting for that handset only (when
programming from a cordless handset only).
Base - Change the setting for the telephone base only.
4. q or p to choose On or Off -> SELECT.
•
•
•
Answering system
About answering system and voicemail
Your telephone has separate indicators for two different types of voice messages:
those left on the built-in answering system and those left at your telephone
service provider’s voicemail. To listen to messages recorded on the built-in
answering system, refer to the Message playback section on the next page; to
listen to voicemail, contact your telephone service provider for more information.
Turn answering system on/off
The answering system must be turned on to answer and record messages.
Using a cordless handset:
1. MENU.
2. q or p -> Answering sys --> SELECT.
3. q or p -> Answer ON/OFF --> SELECT.
4. q or p -> On or Off --> SELECT.
When the answering system is on, the handset shows ANS ON.
Using the telephone base:
Press /ANSWER ON/OFF to turn the answering system on or off. If the
answering system is turned on, it announces, “Calls will be answered.” If the
answering system is turned off, it announces, “Calls will not be answered.”
•
Message alert tone
When this feature is on, and there is at least one new message, the telephone
base beeps every 10 seconds.
Using a cordless handset or the telephone base:
1. MENU -> q or p -> Answering sys -> SELECT.
2. q or p -> Ans sys setup -> SELECT.
3. q or p -> Msg alert tone -> SELECT.
4. q or p -> On or Off -> SELECT.
Call screening
Use this feature to choose whether incoming messages can be heard over at
telephone base when they are being recorded. If you turn call screening on, you
hear the incoming message. While monitoring an incoming message, you can
answer the call by pressing PHONE on the handset, or pressing /SPEA�ERSPEA�ER
or lifting the corded handset on the telephone base.
Using a cordless handset or the telephone base:
1. MENU -> q or p -> Answering sys -> SELECT.
2. q or p -> Ans sys setup -> SELECT.
3. SELECT to select Call screening.
4. q or p -> choose On or Off -> SELECT.
For more detailed instructions, please refer to the Abridged user’s manual
provided in your package, or for a full set of installation and operation
instructions, refer to the online CL84102/CL84152/CL84202/CL84252/
CL84342/CL84352 DECT 6.0 corded/cordless telephone/answering system
with caller ID/call waiting Complete user’s manual at
www.telephones.att.com/manuals.
For customer service or product information, visit our website at
www.telephones.att.com or call 1 (800) 222-3111. In Canada, dial
1 (866) 288-4268.
© 2011-2014 Advanced American Telephones. All Rights Reserved.
AT&T and the AT&T logo are trademarks of AT&T Intellectual Property licensed to
Advanced American Telephones, San Antonio, TX 78219.
Printed in China. Issue 2.0 AT&T 10/14.
Directory
The directory can store up to 50 entries, which are shared by all system devices.
Operation Steps
Adding an entry 1. MENU.
2. q or p -> Directory -> SELECT.
3. q or p -> Add contact -> SELECT.
4. Enter a telephone number up to 30 digits -> SELECT.
5. Enter a name up to 15 characters -> SELECT.
Searching/dialing
an entry
1. DIR in idle mode.
2. Press q or p to browse through the directory, or press
the dialing keys (0-9) to start a name search.
3. Press PHONE or /SPEA�ER on a handset to call.
-OR-
On the telephone base, press /SPEA�ERSPEA�ER or lift the
corded handset to call.
Message playback
Using the telephone base:
Press /PLAY when the telephone base is in idle mode. If there are only new
or only old messages, they are played automatically. If there are both old and new
messages, press q or p -> Play new msgs or Play old msgs -> SELECT.
Using a cordless handset:
Press MENU twice when the handset is in idle mode. If there are only new or
only old messages, they are played automatically. If there are both old and new
messages, press q or p -> Play new msgs or Play old msgs -> SELECT.
Options during playback
Feature On the telephone base On a handset
Adjust playback volume
Press q/VOL/p
Press qVOLUME or
pVOLUME
Stop playback
Press /STOP
Press 5
Skip to the next message Press /S�IP Press 6
Repeat the message Press /REPEAT Press 4
Play the previous message Press /REPEAT twice Press 4 twice
Delete the message Press X/DELETE Press DELETE
Answering system (continued)
To Previous Page
Loading...
Need help?
General
