ATD Tools ATD-7462 - Lowering Operation; Maintenance and Inspection; Lubrication and Cleaning; Damaged Equipment Handling

3
Model: ATD-7462
Capacity: 2 Ton
ͻ Turn the handle slowly counter-clockwise to lower the jack to its lowest posi on.
ͻ Do not get under or let anyone get under the vehicle while lowering.
ͻ Once completely lowered, remove the unit and return it back to its storage loc
on.
Lubrica on and Cleaning
x Periodically clean and lubricate all moving parts and pivot points.
Damaged Equipment
Any jack that appears to be damaged in any way, is found to be worn, or operates abnormally SHALL BE REMOVED
FROM SERVICE. It is recommended that in this event, the jack be replaced. No repairs are authorized and no parts
Altera ons
Because of poten al hazards associated with this type of equipment, no alter ons shall be made to the product.
A achments and Adapters
x Visual inspec on shall be made before each use of the device by checking for abnormal condi ons, such
as cracked welds, leaks, and damaged, loose, or missing parts.
x Other inspec
ons shall be made per product opera ng instruc ons.
x This device shall be inspected immediately if the device is believed to have been subjected to an abnormal
load or shock. It is recommended that this inspec
on be made byĂƋƵĂůŝĮĞĚƐĞƌǀŝĐĞĂŶĚƌĞƉĂŝƌĨĂĐŝůŝƚLJ
x Owners and/or operators should be aware that repair of this equipment may require specialized
knowledge and facili
es. It is recommended that an annual inspec on of the product be made by a
supplier’s speciĮed parts.
This Jack should be stored in a dry locĂƟon.
Symptom Possible Causes Solu on
The jack will not lower
completely.
1. The threads on the adjustment
rod may be bent not allowing the
jack to fully lower.
1. Transfer the weight to another
jack and replace the jack.
Jack will not hold the load.
1. Overall damage to the jack. 1. Replace the jack.
Jack will not rise.
1. Check to see if there is damage to
the adjustment rod.
2. Lubrica
on needed on moving
components
1. Replace the jack
2. Lubricate moving parts and test
func on again.
Jack will not li the load.
1. The weight of the unit being li ed
is too high.
1. Decrease the weight of object
being li
ed or purchase a higher
capacity jack.
Jack arm will not lower.
1. The threads on the adjustment
rod may be bent not allowing the
jack to fully lower.
1. Replace the jack.
LOWERING
MAINTENANCE
INSPECTION
STORAGE
TROUBLESHOOTING
are available for this jack.
dŚĞƌĞĂƌĞŶŽĂƩĂĐŚŵĞŶƚƐŽƌĂĚĂƉƚĞƌƐĂǀĂŝůĂďůĞŽƌĂƵƚŚŽƌŝnjĞĚĨŽƌƵƐĞǁŝƚŚƚŚŝƐũĂĐŬŶLJƵƐĞŽĨĂƩĂĐŚŵĞŶƚƐŽƌ
adapters could result in property damage, injury or death.
ƋƵĂůŝĮĞĚƐĞƌǀŝĐĞĂŶĚƌĞƉĂŝƌĨĂĐŝůŝƚLJĂŶĚƚŚĂƚĂŶLJĚĞĨĞĐƟǀĞĚĞĐĂůƐŽƌƐĂĨĞƚLJůĂďĞůƐďĞƌĞƉůĂĐĞĚǁŝƚŚƚŚĞ