Need help?Do you have a question about the ATEME Kyrion DR5000 and is the answer not in the manual?
General| Brand | ATEME |
|---|---|
| Model | Kyrion DR5000 |
| Category | Media Converter |
| Language | English |
Details document title, revision number, date of issue, and reference.
States the document is for information only and ATEME assumes no liability for errors or omissions.
Covers copyright notices, trademarks, and limitations of use for ATEME products and documentation.
Outlines safety precautions for operating, maintaining, and handling the device to prevent electrical shock and damage.
Lists the items included in the product package, such as the device, power cord, and documentation.
Describes the front panel interface of the Kyrion DR5000, including air intakes and front panel connectors.
Describes the rear interfaces of the Kyrion Decoders, showing different configurations.
Details the four 75 Ohms F-Type input connectors for DVB-S/S2 signals and their use.
Explains the BNC connectors for ASI input and ASI output (loopback) on the DR5000.
Describes the three SDI output connectors and their grouping for outputting SDI signals.
Details the synchronization interfaces (SYNC IN/OUT) for locking the decoder to an external clock source.
Covers the two Gigabit Ethernet interfaces used for TS reception and streaming.
Describes the 100 Mb management Ethernet port for SNMP and web GUI access.
Details the four independent digital AES/EBU outputs via BNC connectors for audio tracks.
Explains the optional analog audio outputs via Sub-D25 connector and configurable audio tracks.
Explains how air ventilation prevents temperature rises and shows intake/output locations.
Provides step-by-step instructions for unpacking, racking, and connecting the DR5000 unit.
Guides on configuring the Management IP address and accessing the Web GUI.
Lists the three ways to configure the Kyrion: Front Panel, Web Interface, and SNMP.
Describes front panel elements like LEDs, LCD, TFT, keypad, and USB connector.
Overviews the Web GUI structure, divided into Decoding Status and Configuration panels.
Explains the panels for monitoring decoder activity, including rear panel status and active service overview.
This is the entry point for configuring the DR5000, divided into three main sub-sections.
Describes the panel shown upon connecting to the Web GUI, with sub-tabs for System Info and System Notes.
Discusses sub-panels for decoding configuration, focusing on 'preset' management.
Used to configure system settings like network, time, alarms, and BISS/CA.
Describes setting the input type (ASI, DVB-S/S2, IP, ZIXI) to carry the Transport Stream.
Details selecting the ASI input connector for ASI input configuration.
Introduces DVB-S/S2 input setup requiring parameter configuration before stream reception.
Introduces IP input setup requiring parameter configuration before receiving a transport stream.
Explains the DR5000's failover capability for switching between IP sources based on conditions.
Covers SMPTE 2022-7 support for seamless switching between two or more streams.
Details IP SSM settings for subscribing to specific sources within a multicast group using IGMP V3.
Discusses VBR support for streams with varying PCR rates, used for NULL packet removal.
Explains setting up ZIXI input by configuring IP interface and listening port.
Lets you choose which service/PIDs to decode and map audio to output pairs.
Describes the three service selection modes: Auto, Auto-Service, and Pid-Locked.
Panel for selecting video PID in 'pid-locked' mode, otherwise automatically selected.
Details the twelve output pairs and mapping audio inputs to output channels.
Presents five operating modes for audio outputs: Auto, Monitor, PCM, Pass-Through, DolbyE.
Explains automatic PID selection and mapping for audio outputs in non-pid-locked modes.
User is responsible for exact audio mapping in Pid-Locked mode.
Descrambles streams using BISS or DVB-CI CAM modules; modes are exclusive.
Details BISS descrambling modes (BISS 1, BISS E) and key entry.
Explains CAM slot selection rules for descrambling operations based on service selection modes.
Choose which data (ANC/VBI) to process and output, or 'burn' onto video for monitoring.
Inserts configurable ANC data into Ancillary space, with options for insertion, source, and line location.
Details SMPTE standards for time code, SCTE messages, AFD, and caption data carriage.
Describes VBI data modulation in VBI space for SD, with selectable data sources.
Monitors data by burning subtitles, closed captioning, or teletext into the active video portion.
Adjusts SDI output parameters to output a valid SDI stream after input and service configuration.
Organizes SDI connectors and controls pixel range, PsF output, and synchronization.
Synchronizes the DR5000 with external clock references like genlock or VPSC signals.
Controls HD-SDI to SD conversion and sets emulation patterns for output failures.
Front panel monitor that can be disabled on a configuration basis.
Forwards streams on ASI or IP interfaces, allowing descrambling and remuxing before output.
Performs ASI forwarding through two mirrored ASI output connectors.
Configures up to 3 IP outputs using Ethernet 'Stream' connectors for raw, descrambled, or remuxed streams.
Removes services payloads from the stream, based on raw or descrambled stream.
Outputs IP traffic encapsulated in Transport Stream as per ETSI 301192.
Guides on updating license settings via the System tab in the Web GUI.
Provides steps to access the maintenance menu for recovering from system issues or reboots.
Guide for interfacing DR5000 via NMS or SNMP commands; covers Ethernet and protocol.
Explains MIB structure and naming conventions for parameter application and finding equivalences.
Organizes the DR5000 MIB into thirteen nodes, listing their OIDs and brief descriptions.
Demonstrates MIB usage for identification, configuration lock, and system reboot.
Configures network interfaces (LAN/VLAN) via dr5000NetworkConnection, including IP settings.
Configures IP routes using dr5000NetworkRoute for managing routes to hosts or networks.
Describes saving and loading configurations as 'presets' using MIB nodes.
Configures ASI input by setting the input type and selecting the ASI interface.
Configures basic IP input using parameters and checks status via SNMP.
Configures IP input with FEC by enabling the feature and retrieving FEC statistics.
Configures IP failover by setting parameters and activating the feature for source switching.
Configures DVB-S/S2 input by setting type and using the InputSat node for parameters.
Selects automatic composition mode and audio types, with PID mapping performed automatically.
Configures video PID and audio mapping manually in pidlocked mode for composition.
Configures BISS-E descrambling by setting mode and using injected IDs.
Activates and configures clock synchronization using genlock signals for output clock control.
Enables IP forwarding for descrambled or remuxed streams to specified IP destinations.
Configures stream remuxing for ASI and IP forwarding, specifying services and bitrate.
Checks composition results for video and audio, referencing active service overview.
Provides TS descriptor information, including program count, service details, and selected service status.
Explains how to retrieve input statistics files from the Web GUI or Firmware/Troubleshooting tabs.
Details the file format for ASI, IP, and IP with Failover input statistics.
Provides product identification details, including model name.
Details physical characteristics like interface types, number of ports, and connector types.
Covers specifications for SNMP, web server, front panel, and DVB-SSU.
Lists supported video codecs, profiles, and maximum bitrates.
Details video output standards, genlock support, emulation patterns, and downscaling.
Specifies supported audio formats, decoding pairs, and pass-through capabilities.
Lists supported data types like Teletext, CC, and VPS, and their standards.
Details BISS and DVB-CI descrambling capabilities, including bitrate and program limits.
Covers functions like FEC, failover, ZIXI, IP source filtering, and ASI forwarding.
Provides details on DVB-S/S2 modulation, frequency range, input level, and roll-off.
Details audio output drive capacity, connector type, levels, and frequency response.
Lists available software licenses and their present status.
Specifies operating and storage temperature, and operating humidity.
Details physical parameters like mass storage and weight.
Details input voltage range and power consumption.
Lists compliance with Council Directives for emissions and immunity.
Details compliance with safety directives like IEC 60950-1.
Lists compliance with standards for shock and vibration testing.
Lists relevant directives for CE marking compliance.
Specifies compliance with EU RoHS2 and WEEE Directives.
Provides contact information and preparation steps for technical support.
Links to ATEME website for more information and documentation.
Offers assistance with product information, sales, and registration.
To Next Page