EElleeccttrriiccaal l ssyysstteemm 1100..1199
TTeemmppeerraattuurre e mmeeaassuurreemmeenntt AATTLLEET T SSEERRVVIICCE E MMAANNUUAALL
1100..77 TTeemmppeerraattuurre me meeaassuurreemmeenntt
0
0
TTemperature measurements are made up emperature measurements are made up to software to software version 3.41 using NTCversion 3.41 using NTC
resistance (Negative Temresistance (Negative Temperature Coefficient). The perature Coefficient). The temperature can be temperature can be shown fromshown from
0 to approx. 150 C. ATC has 6 channels to measure the temperature.0 to approx. 150 C. ATC has 6 channels to measure the temperature.
When the temperature is too high the driver receives an error message on theWhen the temperature is too high the driver receives an error message on the
displaydisplay. This takes place . This takes place in two stages. The temperature limits in two stages. The temperature limits can be set from can be set from thethe
service menu function. The first service menu function. The first stage involves an error message and the stage involves an error message and the secondsecond
stage involves a new error stage involves a new error message and e.g. the pump/drive motor being shutdown.message and e.g. the pump/drive motor being shutdown.
The following statistics are saved for the temperature:The following statistics are saved for the temperature:
The number of times The number of times the temperature range has been reached in intervals:the temperature range has been reached in intervals:
The temperatures that apply up to software version 3.41 are shown below.The temperatures that apply up to software version 3.41 are shown below.
The temperatures that apply from The temperatures that apply from software version 3.42 are shown below.software version 3.42 are shown below.
Only the oil temperature is measured with NTC resistance in AC Power Plus.Only the oil temperature is measured with NTC resistance in AC Power Plus.
In the drive and pump motor systems the temperature is measured in the In the drive and pump motor systems the temperature is measured in the regulatorsregulators
and motors using and motors using PPTC resistors. The TC resistors. The temperature is reported ttemperature is reported to the o the AATC via TC via thethe
CAN network.CAN network.
OOiill MMoottoorrs s aannd d rreegguullaattoorrss
TTeemmpp. . aabboovve e 7755 C C aabboovve e 112200 CC
TTeemmp p 771 1 - - 7755 CC 11111 1 - - 112200 CC
TTeemmp p 666 6 - - 7700 CC 11001 1 - - 111100 CC
TTeemmp p 661 1 - - 6655 C C 991 1 - - 110000 CC
TTeemmp p 556 6 - - 6600 C C 881 1 - - 9900 CC
OOiill MMoottoorrs s aannd d rreegguullaattoorrss
TTeemmp p aabboovve e 7700 C C aabboovve e 112200 CC
TTeemmp p 661 1 - - 7700 CC 11001 1 - - 112200 CC
TTeemmp p 551 1 - - 6600 CC 881 1 - - 110000 CC
TTeemmp p 441 1 - - 5500 C C 661 1 - - 8800 CC
TTeemmp p uup p tto o 4400 C C uup p tto o 6600 CC
° ° °°
° ° °°
° ° °°
° ° °°
° ° °°
° ° °°
° ° °°
° ° °°
° ° °°
° ° °°
To Next Page
Loading...