Audi Avant RS2 User Manual

Details on engine identification and specifications.

Steps for diagnosing the Motronic system.

Guide for setting engine parameters using diagnostic tool.

Instructions for removing and installing the engine.

Service procedures for the crankshaft group.

Dismantling, assembling, and testing the fuel pump.

Removing and installing parts of the charge air cooler.

Testing the exhaust gas turbocharger and blow-off valve.

Procedures for testing system pressure and holding pressure.

Procedures for replacing the front wheel bearing housing.

Removing and installing ABS components on the front axle.

Procedures for servicing front and rear brakes.

Servicing, removing, installing, and adjusting the handbrake.

Diagram showing relay positions for various systems.

Layout and assignment of front and rear auxiliary relay carriers.

Detailed electrical diagram of the immobilizer system.

Diagram for Motronic unit and trailer recognition connections.

Electrical diagram for Motronic unit and heated rear window.

Diagram for turn signal and hazard warning systems.

Diagram for bulb monitoring and trailer coupling.

Diagram for trailer coupling and rear fog light.

Diagram for electrically adjustable driver and passenger mirrors.

Location for stamping of engine number.

Detailed specifications of engine features like displacement, torque, etc.

Table listing faults, causes, effects, and rectifying actions.

Explanation of readouts for basic engine setting using V.A.G 1551.

Analysis of faults displayed in group 03.

Analysis of faults displayed in group 04.

Information on coding variants for the Motronic control unit.

Information on modifications related to engine removal and installation.

Notes and information on crankshaft group modifications.

Note regarding metal cylinder head gasket installation.

Important notes on metal swarf and oil level for lubrication system.

Information on modified coolant pipe and drive gear for coolant pump.

Dismantling, assembling, and testing the fuel pump.

Removing and installing parts of the charge air cooler.

Testing the exhaust gas turbocharger and blow-off valve.

Technical specifications for Motronic components.

Procedures for testing injection system pressure and holding pressure.

Procedures for testing injector resistance and quantity injected.

Testing the altitude sender and its signal path.

Procedure for testing the voltage supply to the altitude sender.

Testing cable connections for the altitude sender.

Explanation of engine output reduction when towing a trailer.

Procedures for removing and installing the exhaust system components.

Details on intermediate pipes, tail silencer, and catalytic converter suspension.

Information on the separation point between centre and tail silencers.

Details on the installation position of the corrugated tube.

Procedure for aligning the exhaust system to avoid noise and stress.

Alignment of intermediate pipes and double clips.

Procedure for checking the exhaust system for leaks.

Step-by-step guide for replacing the wheel bearing housing.

Procedures for pressing out the wheel hub and bearing.

Instructions for removing and installing suspension strut and drive shaft.

Procedures for removing and installing the drive shaft.

Details on axle link and coupling rod service procedures.

Pressing off track rod joint and tightening nuts.

Procedures for replacing the rear wheel bearing housing.

Procedures for pressing out rear wheel hub and bearing.

Procedures for pressing in wheel hub and bearing.

Procedures for removing and installing the rear drive shaft.

Instructions for fitting 17" cup design wheels with asymmetric hump.

Instructions for removing tyres from wheels.

Details on wheel sizes, tyre sizes, and offsets for summer and winter.

Removing and installing ABS components on the front axle.

Routing of wiring for the speed sensor at the strut and wheelhouse.

Removing and installing ABS components on the rear axle.

Routing of wiring for rear speed sensors at the subframe.

Procedures for servicing the front brake system (Brembo calipers).

Step-by-step guide for replacing brake pads.

Instructions for installing brake pads and checking caliper installation.

Information on damping plates, springs, and mounting plates for brake pads.

Procedures for servicing rear brake discs and brake pads.

Note on replacing damping plates each time brake pads are renewed.

Procedures for removing, installing, and servicing the handbrake.

Installing handbrake shoes, adjusting the handbrake.

Procedures for removing and installing handbrake cables.

Procedure for adjusting the handbrake lever and cables.

Servicing the four-piston fixed caliper brake system.