Description of the remote controller
CD PLAYER functions
• STANDBY CD: turns-on and turns-off the device. If you make the unit exit from the
standby mode using the remote standby CD switch, after the vacuum tube heating
procedure has ended, the CD Player will be selected as the source.
• PLAY / PAUSE : for the description of the function refer to the front panel description.
• STOP / OPEN: for the description of the function refer to the front panel description.
• PREV / REW: for the description of the function refer to the front panel description.
• NEXT / FFW: for the description of the function refer to the front panel description.
• 0123456789 (NUMERIC KEYS): According to the functioning state of the CD player you
have two different actions:
when the CD player is stopped it is possible to select a track pressing the number of
the corresponding song (the apparatus waits for PLAY to be pressed).
When the CD player is playing, pressing the number of the desired song it
immediately skips to the indicated track.
• TIME: for the description of the function refer to the front panel description.
• RPT (REPEAT): for the description of the function refer to the front panel description
Note: the above mentioned keys are active only when the device is in “CD Player” mode.
TUNER Functions
• STANDBY TUNER: switches-on and switches-off of the device. If you make the unit exit
from the standby mode using the remote standby tuner switch, after the vacuum tube heating
procedure has ended, the tuner will be selected as the source.
• SEARCH+: a single press of this button increases the tuning frequency by one step, a
continuous pressure of a few seconds activates a fast research increasing the tuning
frequency by 5 steps.
• SEARCH-: a single press of this button decreases the tuning frequency by one step, a
continuous pressure of a few seconds activates a fast research decreasing the tuning
frequency by 5 steps.
• SCAN+: the tuning frequency is increased to reach the first radio station which has a higher
frequency than the one it started from; if this is not possible a complete scansion of the
band is carried out and the frequency present at the time the switch was pressed is tuned
again.
• SCAN-: the tuning frequency is decreased to reach the first radio station which has a lower frequency than the one it started
from; if this is not possible a complete scansion of the band is carried out and the frequency present at the time the switch
was pressed is tuned again.
• 0123456789 (NUMERIC KEYS): according to the functioning state of the Tuner you have two different actions:
When the tuner is in STORE mode, it is possible to select, using the numeric keys, the position in which you want to
memorize the station, and after it is possible to save it by pressing the STORE key.
When the tuner is not in STORE mode it is possible to select, using the numeric keys, the preset number in order to
recall a station that has been previously memorized.
• AM / FM: permits you to select between AM and FM.
• MEMORY+: MEMORY+ function, for the description of the function refer to the front panel description.
• MEMORY-: MEMORY- function, for the description of this function refer to the front panel description.
• STORE: for the description of the function refer to the front panel description.
• MONO: Pressing this button forces the unit into monophonic playback. When this option is enabled, the STEREO LED turns
off. To return to normal mode, just press this button once. When the unit is in stereophonic mode, the STEREO LED turns
on when the incoming signal is stereophonic, otherwise it stays off.
Note: the above mentioned keys are active only when the device is in “Tuner” mode.
AMPLIFIER functions
• STANDBY AMP: switches-on and switches-off the device. If you make the unit exit from standby mode using the
remote standby AMP switch, after the vacuum tube heating procedure has ended the LINE IN1 will be selected as the
source.
• IN+: it changes the selected source.
• VOLUME+: it increases the volume of the unit.
• IN- : it changes the selected source.
•
VOLUME-: it decreases the volume of the unit.
• MUTE: it activates/de-activates the mute function.
• AMP SETUP: pushing the Amp Setup button the unit enters into setup mode. See the “Setup Menu” paragraph for further
details.
To Next Page
Loading...
Need help?
General