Audio Technica ATM410 User Manual

• Tailored for smooth, natural vocal reproduction
• Cardioid polar pattern reduces pickup of sounds from the sides
and rear, improving isolation of desired sound source
• Durable performance for professional applications
• Hi-ENERGY
®
neodymium magnet for improved output and
transient response
• Excellent off-axis rejection for minimum feedback
• Superior anti-shock engineering for low handling noise
• Multi-stage grille design offers excellent protection against plosives
and sibilance without compromising high-frequency clarity
• Quiet-Flex
™
stand clamp provides silent, flexible microphone
positioning
• Corrosion-resistant contacts from gold-plated XLRM-type
connector
• Rugged, all-metal design and construction for years of trouble-free
use
Output from the microphone's XLRM-type connector is low
impedance (Lo-Z) balanced. The signal appears across Pins 2 and
3; Pin 1 is ground (shield). Output phase is “Pin 2 hot” – positive
acoustic pressure produces positive voltage at Pin 2.
To avoid phase cancellation and poor sound, all mic cables must be
wired consistently: Pin 1-to-Pin 1, etc. For a high-impedance (Hi-Z)
mic input, connect a Lo-Z balanced cable to a Hi-Z matching
transformer (A-T CP8201 or equal) at the equipment input.
When using the ATM410 in settings with a stage monitor speaker,
the speaker should be located 180° off axis (at the rear of the
microphone). This placement, in conjunction with the microphone's
uniform cardioid pickup pattern, will virtually eliminate the possibility
of undesired audio feedback.
Take care to keep foreign particles from entering the windscreen. An
accumulation of iron or steel filings on the diaphragm, and/or foreign
material in the windscreen's mesh surface, can degrade
performance.
Audio-Technica U.S., Inc., 1221 Commerce Drive, Stow, Ohio 44224
Audio-Technica Limited, Old Lane, Leeds LS11 8AG England
www.audio-technica.com
P51802 ©2006 Audio-Technica U.S., Inc. Printed in China
ATM410
ATM410 SPECIFICATIONS
†
ELEMENT Dynamic
POLAR PATTERN Cardioid
FREQUENCY RESPONSE 90-16,000 Hz
OPEN CIRCUIT SENSITIVITY –55 dB (1.7 mV) re 1V at 1 Pa*
IMPEDANCE 300 ohms
WEIGHT 233 g (8.2 oz)
DIMENSIONS 170.0 mm (6.69") long,
53.5 mm (2.11") diameter
OUTPUT CONNECTOR Integral 3-pin XLRM-type
ACCESSORIES FURNISHED AT8470 Quiet-Flex
™
stand clamp
for
5
/
8
"-27 threaded stands;
5
/
8
"-27 to
3
/
8
"-16 threaded adapter;
soft protective pouch
†In the interest of standards development, A.T.U.S. offers full details on its test
methods to other industry professionals on request.
*1 Pascal = 10 dynes/cm
2
= 10 microbars = 94 dB SPL
Specifications are subject to change without notice.
CARDIOID DYNAMIC
VOCAL MICROPHONE
8 kHz
Polar Pattern
SCALE IS 5 DECIBELS PER DIVISION
LEGEND
200 Hz
1 kHz
5 kHz
Frequency in Hertz
LEGEND
12" or more on axis
Frequency Response
Response in dB

Audio Technica ATM410 Specifications

General

Microphone frequency	90 - 16000 Hz
Microphone sensitivity	55 dB
Microphone input impedance	300 Ω
Connectivity technology	Wired
Weight	233 g
Cable type	XLRM

Summary

ATM410 Microphone Features

Tailored Vocal Reproduction

Smooth, natural vocal reproduction for professional applications.

Cardioid Polar Pattern

Reduces side and rear pickup, improving isolation of the desired sound source.

Hi-ENERGY Neodymium Magnet

Provides improved output and transient response for enhanced performance.

Low Handling Noise & Feedback

Features superior anti-shock engineering and excellent off-axis rejection.

Grille and Connector Design

Multi-stage grille protects against plosives/sibilance; gold-plated connector ensures reliable contact.

Durable Construction

Rugged, all-metal design built for years of trouble-free use.

ATM410 Technical Specifications

Element Type

Dynamic microphone element.

Polar Pattern

Cardioid polar pattern for directional sound pickup.

Frequency Response

Frequency range from 90 Hz to 16,000 Hz.

Sensitivity

Open circuit sensitivity of -55 dB (1.7 mV) re 1V at 1 Pa.

Impedance

300 ohms impedance for balanced audio connections.

Dimensions and Weight

Measures 170.0 mm long, 53.5 mm diameter, weighing 233 g (8.2 oz).

Output Connector

Integral 3-pin XLRM-type connector.

Included Accessories

Comes with Quiet-Flex stand clamp, adapter, and protective pouch.

ATM410 Usage and Maintenance

XLRM Connector Wiring

Details low-impedance balanced output, pin assignments, and phase.

Hi-Z Input Connection

Guidance on using balanced cables and matching transformers for Hi-Z inputs.

Feedback Prevention

Advice on stage monitor placement for optimal feedback rejection.

Windscreen Care

Instructions to prevent foreign particles from degrading diaphragm performance.