6
After plugging the DC power adapter into the unit for the first time, “00:00:00” will appear on the LCD display. If you can
receive a DAB+ signal at your location, the unit will synchronize to the current local time. After approximately one minute, the
unit will switch into standby mode. To set the time manually:
1. In Power Off (Standby) mode, press and hold CLOCK SET on remote control or main unit, “TIME SETUP” will appear on
display.
2. Press CLOCK SET to enter the option to set 12- or 24 hour format.
3. Press or on remote control or main unit to select the desired hour format. Press CLOCK SET to confirm.
4. Press or on remote control or main unit to select the SET CLOCK option. Press CLOCK SET to confirm.
5. The hour digits will blink on the display. Press or on the remote control or main unit to adjust the hour.
6. Press CLOCK SET on the remote control to confirm the hour setting, the minute digits will flash to prompt for input.
7. Press or on the remote control or main unit to adjust the minute. Press and hold the button for fast
advance/reverse setting.
8. Press CLOCK SET on remote control again to complete the setting.
NOTE: The following is only functional by using the remote control.
The sleep timer allows you to turn the unit off automatically after a preset time is reached.
1. To activate the sleep timer, turn the unit on and press the SOURCE button to select RADIO, CD, USB, BT or AUX IN.
2. Press the SLEEP button on the remote control. “SLEEP SET” appears on the display.
3. Repeatedly press the SLEEP button to select a sleep time. The unit will turn off after 10, 20, 30, 40, 50, 60, 70, 80 or 90
minutes. Wait for 3 seconds after your selection for the unit to confirm the selection, the unit will play for the selected
length of time then automatically shut down.
4. To cancel the sleep timer, press the SLEEP button repeatedly until the timer on the display shows “OFF”. To turn the unit
off before the selected length of time, press the POWER/STANDBY button at any time.
NOTE: To check the remaining sleep time, press the SLEEP button once. If you are falling asleep to music from an external
device connected to the AUX input, the sleep timer will shut off the power to this system but it will not turn off the external
device.
You can set a time when the device will switch on and off automatically every day.
1. Switch the device to standby mode.
2. Press and hold the TIMER button until “ON TIMER” is shown on the display, the hour digits flash.
3. Use the or button to set the required switch-on time. Select the hours first and confirm by pressing ENTER.
4. Then use the or button to set the minutes and confirm again by pressing ENTER.
5. ”OFF TIMER” appears on the display, the hour digits flash.
6. Use the or button to set the required switch-off time. Select the hours first and confirm by pressing ENTER.
7. Use the or button to set the minutes and confirm again by pressing the ENTER button.
8. Then use the or button to select the mode to be used when device is switched on: DAB, FM, CD, USB, BUZZER
(alarm tone) and press ENTER to confirm.
9. Use the or button to set the required volume and press ENTER to confirm.
Timer setting is now complete. When done successfully, the symbol is shown on the display. To switch off the timer,
proceed as follows:
1. In standby mode, briefly press the TIMER button. The symbol on the display turns off.
2. You can activate the timer with the previously configured settings at any time by pressing TIMER again.
NOTE:
If “Wake to CD/USB” is selected but a CD or USB drive are not inserted, the alarm will default to the Beeping Alarm
automatically when the alarm time is reached. For ‘Wake to Radio”, the system will default to the last FM radio station
listened to prior to switching off. The alarm will increase to the volume level you have set.
ACTIVATE/DE-ACTIVATE ALARM FUNCTION
1. To activate the ALARM, press the TIMER button, and the alarm icon “ ” will show on the LCD display.
2. Cancel the ALARM function by pressing the TIMER button again. The alarm icon “ ” will disappear from the LCD display.
WAKE TO RADIO, CD/USB OR BUZZER ALARM
•When the alarm time is reached, the CD/USB, radio or beeping alarm will sound for 60 minutes, then shut off and reset itself
for the following day (without pressing the snooze button).
•To stop the alarm immediately after it sounds, press the POWER button on remote control or on main unit once. It resets
itself for the following day.
•To cancel the following day alarm, tap the TIMER button once, the alarm icon “ ” will disappear from the LCD display.
If the unit is connected to the mains power and then switched on from standby for the first time, the unit will automatically
enter the DAB mode and perform an automatic scan. During the scan, the display will show “Scanning…” together with a slide
bar that indicates the progress of the scan and the number of stations that have been found so far. Once the scan has
finished, the unit will select the first alphanumerically found station. To explore the found stations, press the or .
To Next Page
Loading...
