Information: Please state type and commission no. of the device (see name plate) when ordering spare parts.
Only original AUMA spare parts should be used. Failure to use original spare parts voids the warranty and exempts
AUMA from any liability. Delivered spare parts may slightly vary from the representation.
TypeDesignationNo.TypeDesignationNo.
Output drive shaft D516.1Sub-assemblyHousing001.0
Snap ring535.1Sub-assemblyBearing flange002.0
Screw plug539.0Sub-assemblyHollow shaft without worm wheel003.0
Sub-assemblyHandwheel with ball handle542.0Sub-assemblyWorm shaft005.0
Output drive sleeve B3/B4/E549.1Motor coupling005.1
Parallel key551.1Coupling pin005.2
Sub-assemblyMechanical position indicator553.0Manual drive coupling005.3
Sub-assemblySocket carrier with motor cable har-
ness
554.0Pull rope005.4
Sub-assemblyPotentiometer for position transmitter556.0Worm wheel006.0
Sub-assemblyPotentiometer without slip clutch556.1Sub-assemblyPlanetary gear for manual drive009.0
Sub-assemblyHeater557.0Sub-assemblyRetaining flange010.0
Sub-assemblyBlinker transmitter including pins at
wires (without impulse disc and insula-
tion plate)
558.0Sub-assemblyTorque lever017.0
Sub-assemblyControl unit with torque switching
heads and switches
559.0-1Gear segment018.0
Sub-assemblyControl unit with magnetic limit and
torque transmitter (MWG) for Non-in-
trusive version in combination with
AUMATIC integral controls
559.0-2Sub-assemblyCrown wheel019.0
Sub-assemblySwitch stack for direction OPEN560.0-1Sub-assemblySwing lever020.0
Sub-assemblySwitch stack for direction CLOSE560.0-2Sub-assemblyDrive pinion II for torque switching022.0
Switch for limit/torque switching560.1Sub-assemblyOutput drive wheel for limit switching023.0
Switch case560.2Sub-assemblyDrive wheel for limit switching024.0
Sub-assemblyPosition transmitter RWG566.0Sub-assemblyLocking plate025.0
Sub-assemblyPotentiometer for RWG without slip
clutch
566.1Sub-assemblyWire for protective earth (pin)058.0
Sub-assemblyElectronic board RWG566.2Sub-assemblyTorque switching head061.0
Sub-assemblyWire harness for RWG566.3Sub-assemblyMotor (VD motor incl. no. 079.0)070.0
Sub-assemblySlip clutch for potentiometer/RWG567.1Sub-assemblyPlanetary gear for motor drive
(SA/SAR 07.1 – 14.1 for VD motor)
079.0
Stem protection tube (without cap)568.1Sub-assemblyPlanetary gear for motor drive
(SA/SAR 16.1 for AD90 motor)
080.0
Cap for stem protection tube568.2Sub-assemblyReduction gearing155.0
V-Seal568.3Sub-assemblyCover for switch compartment500.0
Change-over lever assy569.0Sub-assemblySocket carrier (complete with sockets)501.0
Change-over lever569.1Sub-assemblyPin carrier without pins502.0
Notched pin569.2Sub-assemblySocket for controls503.0
Radial seal output drive A for ISO
flange
574.1Sub-assemblySocket for motor504.0
Stem nut type A575.1Sub-assemblyPin for controls505.0
SetSeal kit, smallS1Sub-assemblyPin for motor506.0
SetSeal kit, largeS2Sub-assemblyPlug cover507.0
Sub-assemblyThreaded plug511.0
Sub-assemblyOutput drive form A (without stem nut)514.0
Sub-assemblyAxial needle roller bearing514.1
70
SA 07.1 – SA 16.1/SAR 07.1 – SAR 16.1 Control unit: electromechanic
Spare parts AC 01.1 Intrusive Modbus RTU
To Next Page
Loading...
