AutomationDirect DURAPULSE Series - Page 310

Index
i–4
P
Parameters: 4–1
Parameters - Communications Parameters
Summary: 5–2
Parameters - Detailed Listings: 4–15
2nd Analog Input Gain - P4.16: 4–44
2nd Analog Input Offset - P4.15: 4–43
2nd Analog Input Offset Polarity - P4.14:
4–43
2nd Source of Frequency Command - P4.13:
4–42
2nd Source of Operation Command - P3.31:
4–39
Accel 1 to Accel 2 Frequency Transition -
P1.08: 4–21
Accel S-Curve - P1.03: 4–19
Acceleration Time 1 - P1.01: 4–18
Acceleration Time 2 - P1.05: 4–20
Analog Input Gain - P4.03: 4–41
Analog Input Offset - P4.02: 4–40
Analog Input Offset Polarity - P4.01: 4–40
Analog Input Reverse Motion Enable - P4.04:
4–41
Analog Output Gain - P4.12: 4–42
Analog Output Signal - P4.11: 4–41
Auto Adjustable Accel/Decel - P6.06: 4–60
Auto Restart after Fault - P6.01: 4–58
Auto Voltage Regulation - P6.04: 4–59
Auto-torque Boost - P2.02: 4–25
Backlight Timer - P8.02: 4–72
Base-Block Time for Speed Search - P6.13:
4–62
Block Transfer Parameters - P9.11-P9.25:
4–75
Braking Voltage Level - P6.18: 4–64
Communication Address - P9.00: 4–73
Communication Protocol - P9.02: 4–73
Control Mode - P2.10: 4–28
DC Injection Current Level - P1.18: 4–23
DC Injection during Start-up - P1.20: 4–23
DC Injection during Stopping - P1.21: 4–23
Decel 2 to Decel 1 Frequency Transition -
P1.09: 4–21
Decel S-Curve - P1.04: 4–20
Deceleration Time 1 - P1.02: 4–18
Deceleration Time 2 - P1.06: 4–20
Derivative Control (D) - P7.22: 4–69
Derivative Filter Time Constant - P7.24: 4–70
Desired Current - P3.17: 4–38
Desired Frequency - P3.16: 4–38
Desired Frequency 2 - P3.20: 4–38
Electronic Thermal Overload Relay - P6.00:
4–57
Encoder Control Output Limit - P10.04:
4–79
Encoder Loss Detection - P10.05: 4–79
Encoder Pulses Per Revolution - P10.00:
4–78
Encoder Type Input - P10.01: 4–78
Fault Records - P6.31-P6.36: 4–65
Feedback Signal Loss Detection Time - P7.26:
4–70
Firmware Version - P9.39: 4–76
Frequency Output (FO) Scaling Factor -
P3.30: 4–39
Frequency Scale Factor - P8.01: 4–72
GS Series Number - P9.41: 4–77
Input Terminal for PID Feedback - P7.00:
4–66
Integral Control - P10.03: 4–78
Integral Control (I) - P7.21: 4–69
Jog Speed: 4–55
Keypad PID Setpoint - P7.10: 4–68
Line Start Lockout - P6.30: 4–64
Loss of AI2 Signal (4-20mA) - P4.05: 4–41
Lower Bound of Output Frequency - P6.16:
4–63
Manufacturer Model Information - P9.42:
4–77
Maximum Allowable Power Loss Time -
P6.12: 4–62
Maximum Speed Search Current Level -
P6.14: 4–62
Mid-point Frequency - P2.04: 4–26
Mid-point Voltage - P2.05: 4–26
Minimum Output Frequency - P2.06: 4–26
Minimum Output Voltage - P2.07: 4–26
Momentary Power Loss - P6.02: 4–58
DURAPULSE AC Drive User Manual
1st Ed. Rev. D 05/2013