i–5
(Parameters - Detailed Listings – continued)
Motor Auto Tune - P0.05: 4–16
Motor Base Frequency - P0.02: 4–15
Motor Base RPM - P0.03: 4–16
Motor Line-to-Line Resistance R1 - P0.06:
4–17
Motor Maximum RPM - P0.04: 4–16
Motor Nameplate Amps - P0.01: 4–15
Motor Nameplate Voltage - P0.00: 4–15
Motor No-Load Current - P0.07: 4–17
Multi-Function Inputs (DI) - P3.01-P3.10:
4–29
Multi-Function Output (RO) - P3.11: 4–36
Multi-Function Outputs (DO) - P3.11-P3.14:
4–36
Multi-Speeds - P5.01-P5.15: 4–56
Over-current Stall Prevention during Accel -
P6.10: 4–61
Over-current Stall Prevention during
Operation - P6.11: 4–61
Over-Torque Detection Level - P6.08: 4–60
Over-Torque Detection Mode - P6.07: 4–60
Over-Torque Detection Time - P6.09: 4–60
Over-Voltage Stall Prevention - P6.05: 4–59
Over-Voltage Stall Prevention Level - P6.17:
4–64
Parameter Copy - P9.40: 4–77
Parameter Lock - P9.07: 4–74
PID Deviation Level - P3.18: 4–38
PID Deviation Time - P3.19: 4–38
PID Feedback Gain - P7.03: 4–67
PID Feedback Loss Operation - P7.27: 4–71
PID Feedback Loss Preset Speed - P7.28:
4–71
PID Multi-setpoints - P7.11-P7.17: 4–68
PID Output Frequency Limit - P7.25: 4–70
PID Setpoint Gain - P7.06: 4–67
PID Setpoint Offset - P7.05: 4–67
PID Setpoint Offset Polarity - P7.04: 4–67
PID Setpoint Source - P7.02: 4–67
Proportional Control - P10.02: 4–78
Proportional Control (P) - P7.20: 4–69
PV 100% Value - P7.01: 4–67
PWM Carrier Frequency - P2.08: 4–27
Restore to Default - P9.08: 4–74
Reverse Operation Inhibit - P6.03: 4–58
Select Method for 2nd Accel/Decel - P1.07:
4–21
Serial Comm Direction Command - P9.28:
4–76
Serial Comm External Fault - P9.29: 4–76
Serial Comm Fault Reset - P9.30: 4–76
Serial Comm JOG Command - P9.31: 4–76
Serial Comm RUN Command - P9.27: 4–76
Serial Comm Speed Reference - P9.26: 4–76
Skip Frequency 1 - P1.10: 4–22
Skip Frequency 2 - P1.11: 4–22
Skip Frequency 3 - P1.12: 4–22
Skip Frequency 4 - P1.13: 4–22
Skip Frequency 5 - P1.14: 4–22
Skip Frequency Band - P1.17: 4–22
Slip Compensation - P2.01: 4–25
Source of Frequency Command - P4.00:
4–40
Source of Operation Command - P3.00:
4–29
Start-point for DC Injection - P1.22: 4–23
Stop Methods - P1.00: 4–18
Time Out Detection - P9.04: 4–74
Time Out Duration - P9.05: 4–74
Torque Compensation Time Constant - P2.03:
4–25
Transmission Speed - P9.01: 4–73
Trim Mode Select - P4.18: 4–45
Trim Reference Frequency - P4.17: 4–44
Upper Bound for Integral Control - P7.23:
4–70
Upper Bound of Output Frequency - P6.15:
4–63
User Defined Display Function - P8.00:
4–72
Volts/Hertz Settings - P2.00: 4–24
Parameters - Lock: 4–74
Parameters - Memory Addresses: 5–4
Parameters - Restore to Default Settings: 4–74
Index
DURAPULSE AC Drive User Manual
1st Ed. Rev. D 05/2013
To Next Page
Loading...