Autoquip American Lifts P-25-005 User Manual (English)

Other manuals for Autoquip American Lifts P-25-005

Questions and Answers:

S
Samuel ThorntonAug 10, 2025
What to do if my Autoquip American Lifts P-25-005 lift does not raise?
- F
  flemingsusanAug 10, 2025
  If your Autoquip Lifting Systems lift isn't raising, try the following: reverse two motor electrical leads. Look for any line or hose leaks. Check the oil level in the reservoir and add the specified oil if it's low. Ensure the load doesn't exceed the rated capacity. Inspect the suction screen for clogs, clean it, and replace the oil. Also, check the suction line for air leaks due to loose fittings and tighten them.
J
Justin BakerAug 15, 2025
Why does the motor on my Autoquip American Lifts P-25-005 labor or heat excessively?
- J
  James MckayAug 15, 2025
  If the motor on your Autoquip Lifting Systems is laboring or overheating, check the voltage at the motor terminals while the pump is running under load. Ensure the wiring matches the diagram on the nameplate for proper voltage connections. Also, check for a low oil level or clogged breather holes in the reservoir fill plug.
J
John TuckerAug 20, 2025
What to do if Autoquip Lifting Systems lift lowers slowly?
- A
  Anna FranklinAug 20, 2025
  If your Autoquip Lifting Systems lift lowers slowly, check for pinched tubing or hoses. If pipe is used, inspect for any obstructions in the line. Also, consider that thick oil due to low ambient temperatures can cause this issue; use a lower weight oil that remains thin in cold conditions (5W-15, etc.). If you see foam in the tank oil, check for loose connections in the suction line between the pump and tank, and tighten them.
S
stevenmillerAug 26, 2025
How to fix Autoquip American Lifts P-25-005 Lifting Systems lift that won't lower?
- S
  Sarah AdamsAug 26, 2025
  If your Autoquip Lifting Systems lift won't lower, start by checking the voltage near the coil. Inspect all fittings, hoses, and hydraulic components for leaks or damage. Try pressurizing the lifting cylinder by briefly pressing the “UP” button, then immediately press the “DOWN” button. If it starts to lower, keep pressing “DOWN” until fully lowered. Wait 10-15 minutes for the hydraulic system pressure to equalize, then press and hold the “DOWN” button to fully lower the lift and bleed air from the system for about 60 seconds.
E
Eddie MoralesAug 30, 2025
Why does my Autoquip Lifting Systems lift raise and then lower slowly?
- I
  iwadeAug 30, 2025
  If your Autoquip Lifting Systems lift raises and then lowers slowly, remove the solenoid coil and check it. If the lift still doesn't hold with the coil removed, remove and clean the down valve cartridge, replacing it if necessary. Also, check the oil line, hose, or fittings for leaks and repair them. The check valve in the pump assembly might not be seating properly, indicated by the pump shaft and motor turning backward on their own without power. If this occurs, replace the pump assembly.
D
Deanna CampbellSep 3, 2025
Why does my Autoquip American Lifts P-25-005 Lifting Systems lift seem bouncy during operation?
- J
  johnmccarthySep 4, 2025
  If your Autoquip Lifting Systems lift seems bouncy during operation, lower the lift to its collapsed position and continue holding the “DOWN” button for an additional 10-30 seconds to bleed air from the cylinder. Also, check for oil starvation.

Autoquip American Lifts P-25-005 Specifications

General

Brand	Autoquip
Model	American Lifts P-25-005
Category	Lifting Systems
Language	English

Autoquip American Lifts P-25-005 User Manual

Table of Contents

Other manuals for Autoquip American Lifts P-25-005

Questions and Answers:

Autoquip American Lifts P-25-005 Specifications