Avaya PARTNER Advanced Communications System - Page 100

100
System Flow Chart—System
System Date
Dial # 1 0 1
Dial the date (MMDDYY)
System Time
Dial # 1 0 3
Dial the time (HHMM-24 hr. military
time)
Number of Lines
Dial # 1 0 4
Dial two digits (01–31) (R4 or later)
or, Dial two digits (01–19 (Prior R4),
for # of outside lines assigned to
every extension. 3 per ACS
processor & 308EC module. 16 for
T1/DSL module. 2 per 206 or 200
module
 . 4 per 400EC module  .
WARNING
Do not use Number of Lines (#104) after
initial setup. In Key mode, the Number of
lines procedure will change Line
Assignment (#301), Line Access
Restriction (#302), Automatic Line
Selection and Line Ringing to factory
settings.
To change line assignments without
affecting other settings, use Line
Assignment (#301).
In Hybrid mode, the Number of Lines
procedure will change Pool Line
Assignment (#207), Pool Extension
Assignment (#314), and Pool Access
Restriction (#315). Additionally, it
changes Line Assignment (#301), Line
Access Restriction (#302), Automatic
Line Selection and Line Ringing. To
change pool assignments without
affecting other settings, use Pool Line
Assignment (#207) and Pool Extension
Assignment (#314).
Transfer Return Rings
Dial # 1 0 5
Dial 1 digit (0–9) for # of rings before
call returns.
0–9 rings
4 rings

0 rings=no return
Recall Timer Durations
Dial # 1 0 7
Dial two digits (01–80) to set length
of a switchook flash
 =18 (450
msec)
Rotary Dialing Timeout
Dial # 1 0 8
Dial 1=4 secs
2=8 secs

3=12 secs
Outside Conference Denial
Dial # 1 0 9
Dial 1=Allowed 
2=Disallowed
Automatic System Answer Delay
Dial # 1 1 0
Dial a ring delay number (0–9)
2 rings

Direct Extension Dial Delay
Dial # 1 1 2
Dial a ring delay number (0–9)
2 rings
 ,
0 rings=answered immediately
Automatic System Answer
Button
Dial # 1 1 1
Dial 1=Assigned,
2=Not Assigned

3=Select Button then press a
programmable button
Direct Extension Dial Button
Dial # 1 1 3
Dial 1=Assigned
2=Not Assigned

3=Select Button then press a
programmable button
Outgoing Call
Restriction
Button
Dial
# 1 1 4
Dial 1=Assigned
2=Not Assigned

3=Select Button then press a
programmable button
Wake Up Service Button
Dial # 1 1 5
Dial 1=Assigned
2=Not Assigned

3=Select Button then press a
programmable button
Ring On Transfer
Dial # 1 1 9
Dial 1=Active 
2=Not Active
Automatic System Answer Mode
Dial # 1 2 1
Dial 1=Hold 
2=Disconnect
3=Ring
Caller ID Type
Dial # 1 2 2
Dial 1=USA 
2=Singapore
Backup Programming Automatic
Dial # 1 2 3
Dial 1=Active Internal
2=Actove PC Card
3=Not Active

Backup Programming—Manual
Dial
# 1 2 4
Dial 1=Internal Memory
2=PC Card
Press
e to begin the backup
Restore Programming
Dial # 1 2 5
Dial 1=Internal Man.mmddyy 
2=PC Card Man.mmddyy
3=Internal AUTO.mmddyy
2=PC Card AUTO.mmddyy
Press
e to begin the restore
Automatic Daylight/
Standard
Times
Dial
# 1 2 6
Dial 1=Active 