To Next PageTo Next Page
Need help?Do you have a question about the AVS Electronics CAPTURE Series and is the answer not in the manual?
General| Brand | AVS Electronics |
|---|---|
| Model | CAPTURE Series |
| Category | Control Panel |
| Language | English |
Detailed technical specifications for the CAPTURE 32 control panel.
Detailed technical specifications for the CAPTURE 16 control panel.
Detailed technical specifications for the CAPTURE 8 control panel.
Configuration for normally open inputs.
Configuration for normally closed inputs.
Configuration for balanced inputs with one resistor.
Configuration for balanced inputs with two resistors.
Diagram and description of the control panel board components.
Description of terminal board, jumper, and connector functions.
Details on the power supply unit specifications and capabilities.
Instructions for connecting XGSM and EWEB WIFI modules.
Technical features and operation of the A500 and A500 Plus keypads.
Procedure for assigning unique addresses to keypads.
Technical details for various satellite modules like XSAT36, XSATWS, XSATHP, etc.
Guidelines for managing system arming modes and priorities.
Information on installing external actuators for arming.
Features and connection details for the PSTN telephone interface.
Features and connection details for the DIGIVOC voice module.
Technical specifications and operation of the XGSM module.
Guide for inserting SIM card and connecting antenna.
Technical specs for XGSM485/PRO, including dual SIM and voice messages.
How to check SIM credit and set expiry date.
Procedures for recording vocal messages.
Using pre-recorded words and custom messages for events.
Customizing zone-specific vocal communications.
List of telephone codes and their associated pre-recorded vocabulary.
Activating RTC functions via telephone call.
List of DTMF commands for remote control.
Configuring SMS messages for technical and alarm events.
Managing incoming SMS commands and syntax.
Managing system sectors for partitioning and zone association.
Managing user access codes and their permissions.
General steps and considerations for system installation.
Defining the type of satellite model connected.
Understanding and configuring zone types and their behavior.
Associating physical inputs with software zones.
Defining the behavior of each zone input (e.g., Instant, Delay).
Configuring optional outputs (Open Collectors) for system expansion.
Setting activation times for Open Collector outputs.
Configuring timing parameters for relays, sirens, and buzzers.
Guidelines for setting time-based output activations.
Managing user codes, partitions, and access permissions.
Defining personalized user settings and function access.
Customizing user profiles for specific keypad functions and system access.
Programming functions for BIP remote controls.
Using the A500Plus reader for TOY/BIP access.
Programming TOYS for access to the control panel.
Acquiring TOYS for system access.
Setting up keypad functions, buzzer behavior, and quick arming.
Enabling audio feedback for events on A500Plus keypads.
Selecting events for vocal communication via A500Plus keypads.
Programming wireless satellite modules and sensors.
Configuring siren and buzzer parameters and activation.
Detailed parameter settings for sirens and buzzers.
Configuring alarm counter, sound tones, and flash behavior.
Programming telephone numbers for alarm and event communication.
Defining communication protocols for event transmission.
Selecting the interface for call forwarding (PSTN, GSM).
Configuring the XGSM module, including PIN and GPRS settings.
Configuring XGSM485 module, including SIM B and GPRS.
Configuring fast format channels for non-zone events.
Defining zone event transmission and vocal messages.
Setting up remote panel reprogramming.
Configuring email parameters for event notification.
Managing the "MY AVS ALARM" app connection.
Setting the system date and time for accurate event logging.
Configuring automatic system tests for batteries and supervision.
Managing automatic armings and OC activations based on time.
Programming annual holiday periods to temporarily disable functions.
Adjusting system time for daylight saving changes.
Configuring network parameters for EWEB/EWEB WIFI devices.
Copying feature settings between different system elements.
Resetting the control panel to default configuration.
Enabling USB connection for interactive programming.
Process for updating control panel firmware.
Performing zone status checks and tests.
Temporarily blocking alarm signals for maintenance.
Resetting installer codes and sector configurations.
