AXE MM2 Series - Key Introduce and Operation Manual; Key Function Descriptions; Pass Code and System Settings; Display and Alarm Parameter Configuration

Key Introduce Operation Manual
 Key Function 1.In normal display,The key function is call out setting group
2.In parameter setting page,The key function is data Enter , and goto next page
 Key Function 1.In normal display,The key function is call out alarm value setting page
2.Into parameter setting page,the parameter mark&data is alternate display,If need modify data can
press shift key into setting procedure,The display is lock parameter data,this time must let off key
about 0.2 sec,press again,the cursor(twinkle express)is cycle moving left.
(Key Response about 0.2
sec)
 Key Function 1.In normal display,The key function is call out adjustment display value (DZERO&DSPAN)page
2.Into parameter setting page,the parameter mark&data is alternate display,If need modify data can
press up key into setting procedure,The display is lock parameter data,this time must let off key
about 0.2 sec,press again,the parameter data will increment. (Key Response about 0.2 sec)
 Key Function 1.In normal display,The key function is call out adjustment analog output (AZERO&ASPAN)page
2.Into par
ameter setting page,the parameter mark&data is alternate display,If need modify data can
press down key into setting procedure,The display is lock parameter data,this time must let off key
about 0.2 sec,press again the parameter data will decrement. (Key Response about 0.2 sec)
 &  Key Function In setting group or setting page press  &  key return normal display,but if in setting page the
modify data will be lost
No Key in anything In setting group or setting page no key in anything about 2 minutes,return normal display
Step Parameter Mark Description
Parameter Mark
Operation Manual
1
Normal display

Press  /FUNC key into P.COD setting page

2
P.COD(Pass code input
page)

1.Key in 5 digit pass code with  or  or  key
2.Press  key,the pass code is right into setting grou
p ,
otherwise
return normal display
3 SYS(System setting group)

ROP(Alarm setting group)

AOP(Analog output setting
group)

DOP(Communication
setting group)

1. Select setting group with  key
2. Press  key into setting page of selection setting group
4
SYS(System setting group)

Press  key decide SYS setting group , press 
key into
DP setting page

4-1
DP(Decimal Point)
Default=0

1. Decide decimal point position with  or  key (0 to 4)
2. Press  key enter data and into DSPL setting page

4-2
DSPL(Display Low Scale)
Default=0

1.Decide display low scale with  &  &  key (-19999~19999)
2.Press  key enter data and into DSPH setting page

4-3
DSPH(Display High Scale)
Default=19999

1.Decide display high scale with  &  &  key (-19999~19999)
2.Press  key enter data and into AVG setting page

4-4
AVG (Average)
Default=1

1.Decide display Average times with  &  &  key (1~99)
2.Press  key enter data and into LCUT setting page

4-5
LCUT (Low Cut)
Default=0

1.Decide display low cut with  &  &  key (0~99)
2.Press  key enter data and into CODE setting page

4-6
CODE(Pass Code)
Default=0

1.Decide Pass code with  &  &  key (0~19999)
2.Press  key enter data and into LOCK setting page

4-7
LOCK(Panel Lock)
Default=NO

1.Decide panel lock with  or  key (NO or YES)
2.Press  key enter data and return SYS setting group
5
ROP(Alarm setting group)

Press  key decide ROP setting group,press  key into
ACT1 setting page

5-1
ACT1(Alarm Active 1
setting page )Default=HI

1.Decide active 1 with  or  key(HI or LO)
2.Press  key enter data and into ACT2 setting page

5-2
ACT2(Alarm Active 2
setting page )Default=HI

1.Decide active 2 with  or  key(HI or LO)
2.Press  key enter data and into ACT3 setting page
All manuals and user guides at all-guides.com