B-K lighting Yukon Bollard

To Next Page

TOOLS

NEEDED:

3/32”, 1/8” & 7/64” Allen Wrench

Waterproof Wire Connectors

Sleeve or Wedge Anchors for Concrete (1/4” Dia. Min.)

7/16” Socket

Yukon Bollard

Warning High Voltage

Installation Instructions

• Product must be installed by a qualified person in a manner

consistent with its intended use and in compliance with the

National Electrical Code, Canadian Electrical Code, and all

Local and Provincial Codes.

• Follow product label information and instructions.

• Qualified Personnel must perform all servicing or relamping

of this product.

• Before wiring to power supply and during servicing or

relamping, turn off power at fuse or circuit breaker before

service.

• The use of accessory equipment not recommended by the

manufacturer or installed contrary to instructions may cause

an unsafe condition. The use of damaged components may

cause an unsafe condition and void product warranty.

IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE ALL

SAFETY AND INSTALLATION INSTRUCTIONS

• Do not block light emanating from product in whole or

part, as this may cause an unsafe condition.

• Never operate the fixture with missing or damaged lens.

Lens must be cleaned on regular basis.

• Entire fixture may become extremely hot. Do not touch hot

lens or fixture body. Do not touch the lamp at any time.

Use a clean, dry, soft cloth to handle the lamp. Oil from

skin may damage the lamp and cause it to rupture.

• Replace lamp only with correct wattage and type of lamp

marked on fixture label.

• All gaskets, o-rings and sealing surfaces must be kept

clean during installation and service; failure to do this may

cause an unsafe condition and void product warranty.

INSTRUCTIONS PERTAINING TO

A RISK OF FIRE, OR INJURY

TO PERSONS IMPORTANT

SAFETY INSTRUCTIONS

Lighted fixture is HOT!

WARNING - To reduce the risk of

FIRE OR INJURY TO PERSONS:

Turn off/unplug and allow to cool before replacing LED.

Fixture gets HOT quickly! Contact only switch/plug when

turning on. Do not touch hot lens, guard, or enclosure.

Keep fixture away from materials that may burn.

Do not operate the luminaire fitting with a missing or

damaged shield. Do not touch the source at any time.

SAVE THESE INSTRUCTIONS

· Suitable for wet locations

IMPORTANT LISTINGS AND CERTIFICATIONS

CONCRETE INSTALLATION ONLY

RELEASED DATE

09/03/2021

REFERENCE NUMBER

INS-2850-00

40429 Brickyard Drive • Madera, CA 93636 • USA

559.438.5800 • FAX 559.438.5900

www.bklighting.com • info@bklighting.com

B-K LIGHTING

THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION OF B-K LIGHTING, INC. AND ITS RECEIPT OR POSSESSION DOES NOT CONVEY ANY RIGHTS TO REPRODUCE, DISCLOSE ITS CONTENTS, OR TO MANUFACTURE, USE OR

SELL ANYTHING IT MAY DESCRIBE. REPRODUCTION, DISCLOSURE OR USE WITHOUT SPECIFIC WRITTEN AUTHORIZATION OF B-K LIGHTING, INC. IS STRICTLY FORBIDDEN.

RE2/RE2: Dual - GFCI w/USB

RE1/RE1: Dual - GFCI

Avaiable Configuration:

Machined

Aluminum

Housing

RE1/RE2: Dual - GFCI & GFCI w/ USB

IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE THESE INSTALLATION

INSTRUCTIONS

Proper soil preparation is recommended before installation. See the DIG-IT guide at www.bklighting.com/collaterals/install/digit.

pdf for more information.

Need help?

Do you have a question about the B-K lighting Yukon Bollard and is the answer not in the manual?

The Yukon Bollard is an outdoor lighting fixture designed for ground-level installation, primarily in concrete. It features a robust machined aluminum housing, ensuring durability and resistance to environmental elements. The bollard is suitable for wet locations, making it ideal for various outdoor settings.

Function Description:

The Yukon Bollard serves as an outdoor lighting solution, providing illumination for pathways, landscapes, and other exterior areas. It can be configured with different wiring options, including incandescent (INC) and 0-10V dimming, to suit various lighting control needs. Additionally, some configurations include integrated GFCI (Ground Fault Circuit Interrupter) receptacles, with or without USB charging ports, offering convenient power access for outdoor tools or devices. The fixture is designed for concrete installation, with a specific anchor kit and base assembly to ensure secure and stable mounting.

Important Technical Specifications:

Tools Needed for Installation:
- 3/32", 1/8", and 7/64" Allen Wrench
- Waterproof Wire Connectors
- Sleeve or Wedge Anchors for Concrete (1/4" Dia. Min.)
- 7/16" Socket
Housing Material: Machined Aluminum
Wiring Configurations:
- INC (Incandescent): Standard line, common, and ground connections.
- 0-10V Dimming: Includes line, common, positive dim, negative dim, and ground connections for dimmable applications.
- Receptacle: Dedicated line, common, and ground connections for GFCI or GFCI with USB receptacles.
Available Configurations (Receptacle Options):
- RE1/RE1: Dual - GFCI
- RE2/RE2: Dual - GFCI w/USB
- RE1/RE2: Dual - GFCI & GFCI w/USB
Installation Type: Concrete installation only.
Anchor Kit: YKB Anchor Kit, requiring four 1/4-20 nuts for securing the base.
Conduit Requirements: Conduit must be run inside the anchor plate center hole prior to pouring concrete.
Electrical Sealing: Requires waterproof silicone sealant (not included) as per NEC guidelines.
Listings and Certifications: Suitable for wet locations, cULus listed.

Usage Features:

Versatile Lighting Control: Supports both standard incandescent wiring and 0-10V dimming, allowing for flexible light output adjustments.
Integrated Power Access: Select models offer GFCI receptacles, with options for USB charging, providing convenient outdoor power for various applications without needing separate outlets.
Durable Construction: The machined aluminum housing ensures longevity and resistance to harsh outdoor conditions.
Secure Mounting: Designed for concrete installation with a dedicated anchor kit, providing a stable and robust fixture.
Easy Wiring Access: The base assembly allows for primary branch circuit wiring and dimming controls to be pulled through and connected within the housing.
Receptacle Cover: If equipped with a receptacle, it includes a cover secured by a set screw for protection.

Maintenance Features:

LED Replacement: The manual advises turning off/unplugging the fixture and allowing it to cool before replacing the LED.
Lens Cleaning: The lens must be cleaned on a regular basis to maintain optimal light output and prevent unsafe conditions.
Gasket and Sealing Surface Maintenance: All gaskets, o-rings, and sealing surfaces must be kept clean during installation and service to prevent unsafe conditions and void product warranty.
Component Replacement: Qualified personnel must perform all servicing or relamping. The use of damaged components may cause unsafe conditions and void the product warranty.
Safety Precautions:
- Always turn off power at the fuse or circuit breaker before wiring or servicing.
- Avoid touching hot lens, guard, enclosure, or the light source itself, as the fixture gets hot quickly.
- Do not operate the luminaire with a missing or damaged shield/lens.
- Keep the fixture away from materials that may burn.
- Handle lamps with a clean, dry, soft cloth to prevent damage from skin oils.
Soil Preparation: Proper soil preparation is recommended before installation, with reference to the DIG-IT guide for detailed instructions. This ensures a stable foundation for the concrete pour.