Need help?Do you have a question about the Bang & Olufsen BeoVision 12-65 MK II and is the answer not in the manual?
General| Screen Size | 65 inches |
|---|---|
| Resolution | 1920 x 1080 pixels |
| Display Technology | Plasma |
| Aspect Ratio | 16:9 |
| Connectivity | HDMI, Component, Composite |
| Speakers | Built-in |
Explains the navigation methods and features within the installation guide.
Details the EU version of the BeoSystem 4 connection panel.
Details the US version of the BeoSystem 4 connection panel.
Details the Korean version of the BeoSystem 4 connection panel.
Explains the process and options for mounting the BeoSystem 4 on a wall.
Provides recommendations for managing temperature when rack mounting.
Specifies the necessary lifting equipment for handling the heavy BeoVision 12-65.
Details the unpacking and setup of the BeoVision 12-65 service stand.
Mentions extending cables and refers to page 11 for details.
Details the cabling required between BeoSystem 4 and a third-party TV.
States that Cat 7 cables should not be extended.
Discusses the use of active HDMI cables or extenders for longer runs.
Explains how to extend the CAN bus cable for the floor stand.
Illustrates the IR blaster end connection.
Illustrates the RJ45 end connection of the IR blaster cable.
Explains the purpose and necessary steps of screen measurement.
Lists the necessary prerequisites for performing screen measurement.
Specifies the required distances for accurate screen measurement.
Details how to start the screen measurement process.
Option to perform screen colour reproduction measurement.
Option to measure the ambient light sensor.
Guidance on ambient lighting conditions for screen measurement.
Explains the warm-up period required before screen measurement.
Preparation steps required before measuring the light sensor.
Guidance on ambient lighting conditions for light sensor measurement.
Details considerations for choosing the correct projector screen size.
Explains screen gain ratings and properties of different screen materials.
Describes different screen styles like motorized, fixed, or flat hanging.
Explains how viewing distance impacts the selection of projector screen size.
Discusses screen size, black drop, and ground clearance for optimal setup.
Details how to centre the projector horizontally and vertically.
Specific advice for placing front speakers in room corners.
Refers to another guide for detailed rear speaker placement information.
Refers to another guide for detailed rear speaker placement information.
Details the configuration for a 7.1 audio system.
General tips for optimizing speaker placement.
Guidelines for positioning the subwoofer for optimal sound.
Section covering various system settings like clock and network links.
Options for adjusting picture quality and settings.
Displays detailed information about the input signal characteristics.
Options for fine-tuning audio settings and sound parameters.
Step-by-step guide on how to enter the Customer Service Menu.
Instructions on how to exit the Customer Service Menu.
Displays software version information for system processors.
Displays version information for PUC (Plug-in Unit Control) components.
Defines the product variant and its specific usage.
Information about the detected tuner variant.
Hardware version of the Video Engine.
Optimizes for echo phenomena in networked systems.
Settings for ML delay to ensure echo-free streaming.
Lists various system parameters that can be reset to default.
Enable or disable control commands sent to a Home Automation interface.
Enable or disable the HbbTV function.
Function to remove burned-in images on plasma panels.
Setting to avoid image flickering with specific projectors.
Used for screen calibration with new screens or replaced components.
Details input signal parameters like VFREQ, HTOTAL, RESOLUTION.
Details output signal parameters like DISP ID and DISP RES.
Setting up Open Collectors for controlling external devices.
Setting timers for scene control actions.
Controls lift operation and related delays for curtains.
Menu point for activating or deactivating BtB functionality.
Possibility to collect and send product data to Bang & Olufsen.
Select and configure Open Collector ports for scene control.
Assign Open Collectors to Control Timers, Lift, or Cinemascope.
Setting timers for actions during cinema mode activation.
Setting timers for actions during cinema mode deactivation.
Configuration for lift operation and related delays.
Control for motorised lens activation for cinemascope formats.
Example of setting timers for a cinema 'On' scenario.
Example of setting timers for a cinema 'Off' scenario.
Example of lift operation in an 'On' scenario.
Example of lift operation in an 'Off' scenario.
Supported output formats when BeoSystem 4 is combined with BeoVision models.
Supported output formats when used with various projectors.
Lists projectors officially supported by the BeoSystem 4.
Detailed dimensions for the BeoVision 12-65 with its floor stand.
Detailed dimensions for the BeoVision 12-65 with its wall bracket.
Recommendations for ensuring proper ventilation for the TV unit.
Information about available HDMI cables for the system.
Details on Power Link cables with RJ45 connectors.
Information on available IR cables for system connectivity.
Discusses extending HDMI cables with active types or extenders.
Specifications for Network Link product cables.
Details on RJ45 to RJ45 Network Link cables.
Information on Network Link plenum cables for specific areas.
Overview of Power Link cable types, variants, and usage.
Information on older, obsolete Power Link cable types.
Pin configuration and availability for 5.0 mm RJ45 Power Link cables.
Pin configuration and availability for 2.5 mm RJ45 Power Link cables.
Details the IR-eye with autocontrast and its connections.
Connection of IR-eye without autocontrast using Network Link cable.
Connection of IR-eye without autocontrast using specific IR cable.
Information on IR-blaster cables.
Wiring details for Network Link Product Cable used directly.
Cabling using Network Link Product Cable to Screw Terminal.
Lists cables used for BeoSystem 4 and BeoVision 4 connectivity.
DIY solution for RS232 adapter cable.
DIY solution for IR adapter cable.
Wiring diagram for external cables connecting BeoSystem 4 to BeoVision 12.
Specifications for the mains inlet connection.
Specifications for the Ethernet network connection.
Specifications for the USB connection port.
Specifications for the five HDMI input ports.
Specifications for the Power Link output ports.
Primary connection details for home integration using PUC 1.
Secondary connection details for home integration using PUC 2.
Primary connection details for IR-blaster/Hotel.
Specifications for the USB-B connection.
Specifications for the External IR input.
Specifications for the HDMI output.
Specifications for the RS232 connection.
Specifications for the IR/Auto Contrast input.
To Next Page
