Barco UDM 4K15 - 13 GUI - Status menu

256 pages

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

189R5911443 /11 UDM

13.1 Status menu overview................................................................................................................. 190

No settings can be modified in the status menu. Its only for consulting.

GUI – Status menu 13

Table of Contents

1 Safety information11
- 1.1 General Considerations12
- 1.2 Important safety instructions13
- 1.3 Product safety labels17
- 1.4 High Brightness precautions: Hazard Distance18
- 1.5 HD for fully enclosed projection systems20
- 1.6 HD in function of modifying optics22
- 1.7 Radio equipment (optional)22
- 1.8 Compliance23
- 1.9 Download Product Manual23
2 Getting Started25
- 2.1 Getting to know the projector26
- 2.2 Power on the projector28
- 2.3 Start image projection29
- 2.4 Switching to ready mode32
- 2.5 Power off projector32
3 Pulse Remote Control Unit33
- 3.1 Pulse RCU, battery installation34
- 3.2 Pulse RCU, protocol setup35
- 3.3 Pulse RCU, function of the on/off button36
- 3.4 Using the RCU36
- 3.5 Pulse RCU, Functionality overview37
- 3.6 Pulse RCU, function of the “button pressed indicator”37
- 3.7 Pulse RCU, function of the “RGB filter” button38
- 3.8 Pulse RCU, functions of the “Projector OSD on/off” button38
- 3.9 Displaying and Programming addresses into the RCU38
- 3.10 Using the XLR connector of the RCU39
- 3.11 Using the mini-jack connector of the RCU39
- 3.12 Pulse RCU, silicone protection sleeve (optional)40
4 Input & Communication41
- 4.1 Introduction42
- 4.2 Local Keypad and LCD panel42
- 4.3 LCD touch panel43
- 4.4 Communication connections44
- 4.5 LED and Button indication chart46
- 4.6 Pulse Quad Combo input Mk II47
- 4.7 Pulse Quad Combo input Mk I48
- 4.8 Pulse Quad DP 1.2 input49
- 4.9 Pulse SFP input50
5 GUI – Introduction51
- 5.1 Overview52
- 5.2 Navigation55
- 5.3 Test Patterns57
6 GUI – Source59
- 6.1 Displaying a single source60
- 6.2 Displaying multiple sources: Stitched layouts60
- 6.3 Connector settings62
- 6.4 No source image64
7 GUI – Image67
- 7.1 Adjusting the contrast68
- 7.2 Adjusting the brightness68
- 7.3 Adjusting the saturation69
- 7.4 Adjusting the sharpness70
- 7.5 Adjusting the gamma correction71
- 7.6 Setting the desired Gamma type72
- 7.7 Tilted brightness uniformity correction74
- 7.8 Digital shift & zoom76
- 7.9 RealColor P780
- 7.10 Setting the output resolution82
- 7.11 Displaying HDR content83
- 7.12 Dynamic contrast84
8 GUI – Installation87
- 8.1 Orientation88
- 8.2 Laser ranging88
- 8.3 Tilt sensor90
- 8.4 Manipulating the rigging frame91
- 8.5 Manipulating the rigging frame, center position93
- 8.6 Configuring the lens, optical zoom and focus94
- 8.7 Configuring the lens, shift94
- 8.8 Configuring the lens, dynamic focus95
- 8.9 Configuring the lens, Shift to center96
- 8.10 Configuring the lens, Shutter mode97
- 8.11 Scaling modes98
- 8.12 Warping99
- 8.13 Blending & masking111
- 8.14 Illumination121
- 8.15 3D projection122
9 GUI – Profiles127
- 9.1 Profiles introduction128
- 9.2 Saving the current projector settings in a profile129
- 9.3 Assigning a created projector profile to a preset130
- 9.4 Deleting a projector profile132
10 GUI – System Settings135
- 10.1 Remote control136
  - 10.1.1 Broadcast address136
  - 10.1.2 Projector address136
  - 10.1.3 IR sensors137
- 10.2 Host name - custom projector name setup138
- 10.3 Communication, LAN setup139
  - 10.3.1 Introduction to a Network connection139
  - 10.3.2 Wired IP address set up140
  - 10.3.3 Wireless IP address set up142
  - 10.3.4 LAN over HDBaseTTM IP address set up145
- 10.4 DMX147
- 10.5 Controlling the front XLR connector149
- 10.6 GSM configuration150
- 10.7 Changing the User Interface language151
- 10.8 Themes152
- 10.9 Units (measurement) system setup152
- 10.10 Controlling the backlight of the LCD Display153
- 10.11 Date and time setup - manually154
- 10.12 Date and time setup - automatically155
- 10.13 Power saving settings157
- 10.14 Lens features160
- 10.15 Factory reset160
- 10.16 Lens Calibration164
- 10.17 Flex brightness165
- 10.18 Flex Resolution167
- 10.19 Rigging frame Calibration168
- 10.20 Electronic Convergence169
- 10.21 Operational mode170
- 10.22 Capture mode171
- 10.23 Login to advanced settings172
- 10.24 List of open source licenses173
11 Advanced Settings175
- 11.1 Remote access – Enable source preview176
- 11.2 Remote access – Enable camera preview177
- 11.3 Advanced Settings – Color178
- 11.4 Advanced Settings – Statistics179
- 11.5 Checking the status of the Laser Banks180
- 11.6 Advanced settings – Tilt sensor calibration181
12 GUI – Projector scheduler183
- 12.1 About the projector scheduler184
- 12.2 Adding a new command in the scheduler184
- 12.3 Edit or Delete a command186
- 12.4 Clearing the scheduler187
13 GUI – Status menu189
- 13.1 Status menu overview190
14 Product maintenance193
- 14.1 Software update194
- 14.2 Cleaning the lens195
- 14.3 Cleaning the exterior of the projector196
- 14.4 Cleaning / replace the air filters196
A Specifications201
- A.1 Specifications for UDM 4K30202
- A.2 Specifications for UDM W30203
- A.3 Specifications for UDM 4K22205
- A.4 Specifications for UDM W22207
- A.5 Specifications for UDM W19208
- A.6 Specifications for UDM 4K15210
- A.7 Specifications for UDM W15212
- A.8 Specifications SDI inputs213
- A.9 Specifications HDMI inputs214
- A.10 Specifications HDBaseT inputs215
- A.11 Specifications DisplayPort 1.2 inputs216
- A.12 Specifications SFP inputs217
B Video timing tables219
- B.1 Overview video timings220
- B.2 Overview video timings SDI Inputs221
- B.3 Overview video timings HDMI 2.0 inputs222
- B.4 Overview video timings DisplayPort 1.2 inputs224
- B.5 Overview video timings HDBaseT inputs226
C DMX chart229
- C.1 DMX chart input board positioning230
- C.2 DMX chart, Basic230
- C.3 DMX chart, Extended231
D WiFi & GSM compliance information235
- D.1 Compliance FCC236
- D.2 Compliance IC236
- D.3 KCC Certification237
E Regulatory information239
- E.1 Product compliance240
- E.2 China RoHS compliance241
- E.3 Taiwan RoHS compliance242
- E.4 Turkey RoHS compliance243
- E.5 Disposal information243
- E.6 Contact information244
- E.7 Production address244
Glossary245
List of tools247
Index249

Other manuals for Barco UDM 4K15

Installation Manual106 pages

User Manual220 pages

Related product manuals

Preview: Barco UDM-4K15-NL

Barco UDM-4K15-NL

Preview: Barco UDM

Preview: Barco UDM W30

Preview: Barco UDM Series

Barco UDM Series

Preview: Barco UDX

Preview: Barco UDX Series

Barco UDX Series

Preview: Barco Freya

Preview: Barco Balder

Preview: Barco RLM W8

Preview: Barco FLM HD20